- 您現在的位置：買賣IC網 > PDF目錄383493 > MAX712-MAX713 (Maxim Integrated Products, Inc.) NiCd/NiMH Battery Fast-Charge Controllers PDF資料下載
參數資料
| 型號： | MAX712-MAX713 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | NiCd/NiMH Battery Fast-Charge Controllers |
| 中文描述： | 鎳鎘/鎳氫電池快速充電控制器 |
| 文件頁數： | 5/18頁 |
| 文件大小： | 168K |
| 代理商： | MAX712-MAX713 |
M
NiCd/NiMH Battery
Fast-Charge Controllers
_______________________________________________________________________________________
5
______________________________________________________________Pin Desc ription
Compensation input for constant current regulation loop
CC
11
Negative terminal of battery
BATT-
12
System ground. The resistor placed between BATT- and GND monitors the current into the battery.
GND
13
Current sink for driving the external PNP current source
DRV
14
Shunt regulator. The voltage on V+ is regulated to +5V with respect to BATT-, and the shunt current
powers the MAX712/MAX713.
V+
15
Trip point for the under-temperature comparator. If the MAX712/MAX713 power on with the voltage-on
TEMP less than TLO, fast charge is inhibited and will not start until TEMP rises above TLO.
TLO
6
Sense input for temperature-dependent voltage from thermistors.
TEMP
7
Open-drain, fast-charge status output. While the MAX712/MAX713 fast charge the battery,
FASTCHG
sinks current. When charge ends and trickle charge begins,
FASTCHG
stops sinking current.
FASTCHG
8
PGM2 and PGM3 set the maximum time allowed for fast charging. Timeouts from 33 minutes to 264
minutes can be set by connecting to any of V+, REF, or BATT-, or by leaving the pin open (Table 3).
PGM3 also sets the fast-charge to trickle-charge current ratio (Table 5).
PGM2,
PGM3
9, 10
Trip point for the over-temperature comparator. If the voltage-on TEMP rises above THI, fast charge ends.
THI
5
PGM0 and PGM1 set the number of series cells to be charged. The number of cells can be set from
1 to 16 by connecting PGM0 and PGM1 to any of V+, REF, or BATT-, or by leaving the pin open (Table
2). For cell counts greater than 11, see the Linear-Mode, High Series Cell Countsection. Charging more
or fewer cells than the number programmed may inhibit
V fast-charge termination.
PGM0,
PGM1
3, 4
PIN
Positive terminal of battery
BATT+
2
Sets the maximum cell voltage. The battery terminal voltage (BATT+ - BATT-) will not exceed VLIMIT x
(number of cells). Do not allow VLIMIT to exceed 2.5V. Tie VLIMIT to VREF for normal operation.
VLIMIT
1
FUNCTION
NAME
2V reference output
REF
16
相關PDF資料 |
PDF描述 |
|---|---|
| MAX712EPE | Octal Buffers And Line Drivers With 3-State Outputs 20-CFP -55 to 125 |
| MAX712ESE | Octal Buffers And Line Drivers With 3-State Outputs 20-CDIP -55 to 125 |
| MAX712MJE | Octal Buffers And Line Drivers With 3-State Outputs 20-LCCC -55 to 125 |
| MAX713CPE | NiCd/NiMH Battery Fast-Charge Controllers |
| MAX713CSE | NiCd/NiMH Battery Fast-Charge Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX712MJE | 功能描述:電池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX713 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Switch-Mode Battery Charger Delivers 5A |
| MAX713C/D | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:NiCd/NiMH Battery Fast-Charge Controllers |
| MAX713CPE | 功能描述:電池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX713CPE+ | 功能描述:電池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。