- 您現在的位置：買賣IC網 > PDF目錄383493 > MAX712-MAX713 (Maxim Integrated Products, Inc.) NiCd/NiMH Battery Fast-Charge Controllers PDF資料下載
參數資料
| 型號： | MAX712-MAX713 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | NiCd/NiMH Battery Fast-Charge Controllers |
| 中文描述： | 鎳鎘/鎳氫電池快速充電控制器 |
| 文件頁數： | 3/18頁 |
| 文件大?。?/td> | 168K |
| 代理商： | MAX712-MAX713 |
ELECTRICAL CHARACTERISTICS (continued)
(I
V
+ = 10mA, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Refer to Typical Operating Circuit All measurements are with respect to
BATT-, not GND.)
Note 1:
The MAX712/MAX713 are powered from the V+ pin. Since V+ shunt regulates to +5V, R1 must be small enough to allow at
least 5mA of current into the V+ pin.
Note 2:
Offset voltage of THI and TLO comparators referred to TEMP.
Note 3:
t
A
is the A/D sampling interval (Table 3).
Note 4:
This specification can be violated when attempting to charge more or fewer cells than the number programmed. To ensure
proper voltage-slope fast-charge termination, the (maximum battery voltage) ÷ (number of cells programmed) must fall
within the A/D input range.
M
NiCd/NiMH Battery
Fast-Charge Controllers
_______________________________________________________________________________________
3
Battery voltage ÷ number of cells programmed
V
FASTCHG
= 10V
V
FASTCHG
= 0.4V
CONDITIONS
V
1.4
1.9
A/D Input Range (Note 4)
μA
10
FASTCHG
High Current
mA
2
FASTCHG
Low Current
UNITS
MIN
TYP
MAX
PARAMETER
__________________________________________Typic al Operating Charac teristic s
(T
A
= +25°C, unless otherwise noted.)
20
1k
100k
1M
10k
10M
CURRENT-SENSE AMPLIFIER
FREQUENCY RESPONSE (with 15pF)
-20
FREQUENCY (Hz)
G
P
-10
0
10
40
-120
-80
-40
0
C2 = 15pF
FASTCHG = 0V
V
OUT
V
IN
-
CURRENT-
SENSE
AMP
BATT-
BATT-
CC
GND
-
+
+
M
A
V
Φ
20
-10
-20
10
1k
CURRENT-SENSE AMPLIFIER
FREQUENCY RESPONSE (with 10nF)
0
10
40
-80
-120
-40
0
FREQUENCY (Hz)
G
P
100
10k
C2 = 10nF
FASTCHG = 0V
M
A
V
Φ
100
0.1
1.95
1.97
2.01
2.05
CURRENT ERROR-AMPLIFIER
TRANSCONDUCTANCE
1
10
VOLTAGE ON CC PIN (V)
D
1.99
2.03
FASTCHG = 0V, V+ = 5V
M
5.8
4.8
0
60
SHUNT-REGULATOR VOLTAGE
vs. CURRENT
5.6
CURRENT INTO V+ PIN (mA)
V
30
5.2
5.0
10
20
50
5.4
4.0
4.4
4.2
4.6
40
DRV NOT SINKING CURRENT
DRV SINKING CURRENT
M
1.0
0
60
ALPHA THERMISTOR PART No. 13A1002
STEINHART-HART INTERPOLATION
1.6
BATTERY TEMPERATURE(
°
C)
T
B
)
30
1.4
1.2
10
20
50
0.2
0.6
0.4
0.8
20
35
30
25
0
10
5
15
40
相關PDF資料 |
PDF描述 |
|---|---|
| MAX712EPE | Octal Buffers And Line Drivers With 3-State Outputs 20-CFP -55 to 125 |
| MAX712ESE | Octal Buffers And Line Drivers With 3-State Outputs 20-CDIP -55 to 125 |
| MAX712MJE | Octal Buffers And Line Drivers With 3-State Outputs 20-LCCC -55 to 125 |
| MAX713CPE | NiCd/NiMH Battery Fast-Charge Controllers |
| MAX713CSE | NiCd/NiMH Battery Fast-Charge Controllers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX712MJE | 功能描述:電池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX713 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Switch-Mode Battery Charger Delivers 5A |
| MAX713C/D | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:NiCd/NiMH Battery Fast-Charge Controllers |
| MAX713CPE | 功能描述:電池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX713CPE+ | 功能描述:電池管理 NiCd/NiMH Battery Fast-Charge Ctlr RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。