Offset error (Fig" />
參數資料
型號： MAX5865ETM+T
廠商： Maxim Integrated Products
文件頁數： 16/26頁
文件大?。?/td> 0K
描述： IC ANLG FRONT END 40MSPS 48-TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
位數： 10
通道數： 4
功率（瓦特）： 2.10W
電壓 - 電源，模擬： 2.7 V ~ 3.3 V
電壓 - 電源，數字： 1.8 V ~ 3.3 V
封裝/外殼： 48-WFQFN 裸露焊盤
供應商設備封裝： 48-TQFN-EP（7x7）
包裝： 帶卷 (TR)
MAX5865
Ultra-Low-Power, High-Dynamic-
Performance, 40Msps Analog Front End
DAC Offset Error
Offset error (Figure 12a) is the difference between the
ideal and actual offset point. The offset point is the out-
put value when the digital input is midscale. This error
affects all codes by the same amount and usually can
be compensated by trimming.
ADC Gain Error
Ideally, the ADC full-scale transition occurs at 1.5 LSB
below full scale. The gain error is the amount of devia-
tion between the measured transition point and the
ideal transition point with the offset error removed.
ADC Dynamic Parameter Definitions
Aperture Jitter
Figure 13 depicts the aperture jitter (tAJ), which is the
sample-to-sample variation in the aperture delay.
Aperture Delay
Aperture delay (tAD) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken (Figure 13).
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error) and results directly
from the ADC’s resolution (N bits):
SNR(max) = 6.02dB x N + 1.76dB (in dB)
In reality, there are other noise sources besides quanti-
zation noise: thermal noise, reference noise, clock jitter,
etc. SNR is computed by taking the ratio of the RMS
signal to the RMS noise. RMS noise includes all spec-
tral components to the Nyquist frequency excluding the
fundamental, the first five harmonics, and the DC offset.
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS sig-
nal to the RMS noise. RMS noise includes all spectral
components to the Nyquist frequency excluding the
fundamental and the DC offset.
Effective Number of Bits (ENOB)
ENOB specifies the dynamic performance of an ADC at a
specific input frequency and sampling rate. An ideal
ADC’s error consists of quantization noise only. ENOB for
a full-scale sinusoidal input waveform is computed from:
ENOB = (SINAD - 1. 76) / 6.02
Total Harmonic Distortion (THD)
THD is typically the ratio of the RMS sum of the first five
harmonics of the input signal to the fundamental itself.
This is expressed as:
where V1 is the fundamental amplitude and V2–V6 are
the amplitudes of the 2nd- through 6th-order harmonics.
Third Harmonic Distortion (HD3)
HD3 is defined as the ratio of the RMS value of the third
harmonic component to the fundamental input signal.
Spurious-Free Dynamic Range (SFDR)
SFDR is the ratio expressed in decibels of the RMS
amplitude of the fundamental (maximum signal compo-
nent) to the RMS value of the next-largest spurious
component, excluding DC offset.
Intermodulation Distortion (IMD)
IMD is the total power of the intermodulation products
relative to the total input power when two tones, f1 and
f2, are present at the inputs. The intermodulation prod-
ucts are (f1 ±f2), (2 f1), (2 f2), (2 f1 ±f2), (2 f2
±f1). The individual input tone levels are at -7dBFS.
3rd-Order Intermodulation (IM3)
IM3 is the power of the worst third-order intermodula-
tion product relative to the input power of either input
tone when two tones, f1 and f2, are present at the
inputs. The 3rd-order intermodulation products are (2 x
f1 ±f2), (2 f2 ±f1). The individual input tone levels are
at -7dBFS.
THD
(V +V +V +V +V )
V
2
3
2
4
2
5
2
6
2
1
=
20log
HOLD
ANALOG
INPUT
SAMPLED
DATA (T/H)
T/H
tAD
tAJ
TRACK
CLK
Figure 13. T/H Aperture Timing
______________________________________________________________________________________
23
相關PDF資料
PDF描述
MAX5866ETM+ IC ANLG FRONT END 60MSPS 48-TQFN
MAX5873EGK+D IC DAC 12BIT 200MSPS DUAL 68-QFN
MAX5874EGK+D IC DAC 14BIT 200MSPS DUAL 68-QFN
MAX5875EGK+D IC DAC 16BIT DUAL 200MSPS 68-QFN
MAX5876EGK+D IC DAC 12BIT DUAL 250MSPS 68-QFN
相關代理商/技術參數
參數描述
MAX5865EVKIT 功能描述:數據轉換 IC 開發工具 Evaluation Kit for the MAX5863 MAX5864 MAX5865 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX5866ETM 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX5866ETM+ 功能描述:ADC / DAC多通道 10-Bit 2Ch 60Msps CODEC/AFE RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX5866ETM+T 功能描述:ADC / DAC多通道 10-Bit 2Ch 60Msps CODEC/AFE RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX5866ETM-T 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*