- 您現在的位置：買賣IC網 > PDF目錄384665 > MAX3676 (Maxim Integrated Products, Inc.) 622Mbps, 3.3V Clock-Recovery and Data-Retiming IC with Limiting Amplifier PDF資料下載
參數資料
| 型號： | MAX3676 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | 622Mbps, 3.3V Clock-Recovery and Data-Retiming IC with Limiting Amplifier |
| 中文描述： | 622Mbps、3.3V時鐘恢復與數據再定時IC，帶有限幅放大器 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 181K |
| 代理商： | MAX3676 |
M
622Mbps, 3.3V Clock-Recovery and
Data-Retiming IC with Limiting Amplifier
______________________________________________________________________________________
13
allowable pattern-dependent jitter, peak-to-peak
(seconds); and BW = typical system bandwidth, nor-
mally 0.6 to 1.0 times the data rate (Hertz). If the PDJ is
still larger than desired, continue increasing the value of
C
IN
. Note that to maintain stability when using the
MAX3676 analog inputs (ADI+, ADI-), it is important to
keep the low-frequency cutoff associated with C
OLC
below the corner frequency associated with C
IN
(f
C
)
(Table 1).
PDJ can also be present due to insufficient high-fre-
quency bandwidth (Figure 10). If the amplifiers are not
fast enough to allow for complete transitions during sin-
gle-bit patterns, or if the amplifier does not allow ade-
quate settling time, high-frequency PDJ can result.
Pulse-Width Distortion
Finally, PWD occurs when the midpoint crossing of a
0–1 transition and a 1–0 transition does not occur at the
same level (Figure 11). DC offsets and nonsymmetrical
rising and falling edge speeds both contribute to PWD.
For a 1–0 bit stream, calculate PWD as follows:
PWD = [(width of wider pulse) -
(width of narrower pulse)] / 2
Phase Adjust
The internal clock and data alignment in the MAX3676
is well maintained close to the center of the data eye.
Although not required, this sampling point can be shift-
ed using the PHADJ inputs to optimize BER perfor-
mance. The PHADJ inputs operate with differential
input signals to approximately ±1V. A simple resistor
divider with a bypass capacitor is sufficient to set up
these levels. When the PHADJ inputs are not used, they
should be tied directly to V
CC
.
Figure 10. Pattern-Dependent Jitter Due to High-Frequency
Rolloff
A
TIME
MIDPOINT
LONG
CONSECUTIVE
BIT STREAM
0-1-0 BIT STREAM
HF PDJ
Figure 11. Pulse-Width Distortion
A
TIME
MIDPOINT
WIDTH OF A ONE
WIDTH OF A ZERO
PWD RESULTS WHEN THE WIDTH
OF A ZERO DOES NOT EQUAL
THE WIDTH OF A ONE.
t
FALL
≠
t
RISE
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3736 | 3.2Gbps, Low-Power, Compact, SFP Laser Driver |
| MAX3736ETE | 3.2Gbps, Low-Power, Compact, SFP Laser Driver |
| MAX3737ETJ | Full-Duplex LVDM Transceiver 8-MSOP -40 to 85 |
| MAX3737 | Multirate Laser Driver with Extinction Ratio Control |
| MAX3737EGJ | Multirate Laser Driver with Extinction Ratio Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3676E/D | 功能描述:計時器和支持產品 RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MAX3676E/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX3676E/D+ | 功能描述:計時器和支持產品 RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| MAX3676EHJ | 功能描述:時鐘發生器及支持產品 622Mbps 3.3V Clock Recovery RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| MAX3676EHJ+ | 功能描述:時鐘發生器及支持產品 622Mbps 3.3V Clock Recovery RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
發布緊急采購，3分鐘左右您將得到回復。