參數資料
型號： MAX194
廠商： Maxim Integrated Products, Inc.
英文描述： 14-Bit, 85ksps ADC with 10礎 Shutdown(85ksps,單通道,14位串行A/D轉換器)
中文描述： 14位、85ksps ADC，帶有10µ關斷
文件頁數： 21/24頁
文件大?。?/td> 267K
代理商： MAX194
M
14-Bit, 85ksps ADC with 10μA S hutdown
______________________________________________________________________________________
21
Constraints on sequencing the four power supplies are
as follows.
Apply VDDA before VDDD.
Apply VSSA before VSSD.
Apply AIN and REF after VDDA and VSSA are present.
The power supplies should settle within the
MAX194’s power-on delay (minimum 500ns) or you
should recalibrate the converter (pulse RESET low)
before use.
Be sure that digital return currents do not pass through
the analog ground and that return-current paths are low
impedance. A 5mA current flowing through a PC board
ground trace impedance of only 0.1
creates an error
voltage of about 500μV, or about 1LSB error with a ±4V
full-scale system.
The board layout should ensure as much as possible
that digital and analog signal lines are kept separate.
Do not run analog and digital (especially clock) lines
parallel to one another. If you must cross one with the
other, do so at right angles.
The ADC’s high-speed comparator is sensitive to high-
frequency noise on the VDDA and VSSA power sup-
plies. Bypass these supplies to the analog ground
plane with 0.1μF in parallel with 1μF or 10μF low-ESR
capacitors. Keep capacitor leads short for best supply-
noise rejection.
S hutdown
The MAX194 may be shut down by pulling BP/UP/
SHDN low. In addition to lowering power dissipation to
10μW (100μW max) when the device is not in use, con-
siderable power savings is possible by shutting the
converter down for short periods between conversions.
There is no need to perform a reset (calibration) after
the converter has been shut down unless the time in
shutdown is long enough that the supply voltages or
ambient temperature may have changed.
The time required for the converter to “wake up” and
settle depends heavily on the amount of additional error
acceptable. For 0.1LSB additional error, 3.2μs is suffi-
cient settling time and also allows enough time for reac-
quisition of the analog input signal. 20μs settling is
required for less than 0.05LSB error. Figure 23 is a
Figure 21. MAX194 Code Listing for 68HC16 Module and Circuit of Figure 19 (continued)
相關PDF資料
PDF描述
MAX1963 Low-Input-Voltage, 300mA LDO Regulators with RESETin SOT and TDFN
MAX1963ETT Low-Input-Voltage, 300mA LDO Regulators with RESETin SOT and TDFN
MAX1963EZT Low-Input-Voltage, 300mA LDO Regulators with RESETin SOT and TDFN
MAX1976 Low-Input-Voltage, 300mA LDO Regulators with RESETin SOT and TDFN
MAX1976ETT Low-Input-Voltage, 300mA LDO Regulators with RESETin SOT and TDFN
相關代理商/技術參數
參數描述
MAX1940EEE 功能描述:電源開關 IC - USB Triple USB Switch w/Autoreset RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1940EEE+ 功能描述:電源開關 IC - USB Triple USB Switch w/Autoreset RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1940EEE+T 功能描述:電源開關 IC - USB Triple USB Switch w/Autoreset RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1940EEE-T 功能描述:電源開關 IC - USB Triple USB Switch w/Autoreset RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
MAX1945EVKIT 制造商:Maxim Integrated Products 功能描述:1MHZ, 1% ACCURATE, 6A INTERNAL SWITCH STEP-DO - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*