參數資料
型號： MAX1712
廠商： Maxim Integrated Products, Inc.
英文描述： High-Speed, Digitally Adjusted Step-Down Controllers for Notebook CPUs
中文描述： 高速、數字可調、降壓型控制器，用于筆記本電腦
文件頁數： 26/28頁
文件大?。?/td> 437K
代理商： MAX1712
Keep the high-current paths short, especially at the
ground terminals. This practice is essential for stable,
jitter-free operation.
Connect GND and PGND together close to the IC.
Carefully follow the grounding instructions under step
4 of the
Layout Procedure
.
Keep the power traces and load connections short.
This practice is essential for high efficiency. The use
of thick copper PC boards (2 oz vs. 1 oz) can en-
hance full-load efficiency by 1% or more. Correctly
routing PC board traces is a difficult task that must be
approached in terms of fractions of centimeters,
where a single milliohm of excess trace resistance
causes a measurable efficiency penalty.
LX and PGND connections to Q2 for current limiting
must be made using Kelvin sense connections in
order to guarantee the current-limit accuracy. With
SO-8 MOSFETs, this is best done by routing power to
the MOSFETs from outside using the top copper
layer, while tying in PGND and LX
inside
(underneath)
the SO-8 package.
When trade-offs in trace lengths must be made, it’s
preferable to allow the inductor charging path to be
made longer than the discharge path. For example,
it’s better to allow some extra distance between the
input capacitors and the high-side MOSFET than to
allow distance between the inductor and the low-side
MOSFET or between the inductor and the output filter
capacitor.
Ensure that the FB connection to C
OUT
is short and
direct. However, in some cases it may be desirable to
deliberately introduce some trace length between the
FB inductor node and the output filter capacitor (see
the
All-Ceramic-Capacitor Application
section).
Route high-speed switching nodes away from sensi-
tive analog areas (CC, REF, ILIM).
Make all pin-strap control input connections (
SKIP
,
ILIM, etc.) to GND or V
CC
rather than PGND or V
DD
.
Layout Procedure
1) Place the power components first, with ground termi-
nals adjacent (Q2 source, CIN-, COUT-, D1 anode). If
possible, make all these connections on the top layer
with wide, copper-filled areas.
2) Mount the controller IC adjacent to MOSFET Q2,
preferably on the back side opposite Q2 to keep LX-
PGND current-sense lines and the DL gate-drive line
short and wide. The DL gate trace must be short and
wide, measuring 10 to 20 squares (50 to 100 mils
wide if the MOSFET is 1 inch from the controller IC).
3) Group the gate-drive components (BST diode and
capacitor, V
DD
bypass capacitor) together near the
controller IC.
4) Make the DC-DC controller ground connections as
shown in Figure 11. This diagram can be viewed as
having three separate ground planes: output ground,
where all the high-power components go; the PGND
plane, where the PGND pin and V
DD
bypass capaci-
tor go; and an analog GND plane, where sensitive
analog components go. The analog ground plane
and PGND plane must meet only at a single point
directly beneath the IC. These two planes are then
connected to the high-power output ground with a
short connection from V
DD
cap/PGND to the source
of the low-side MOSFET, Q2 (the middle of the star
ground). This point must also be very close to the out-
put capacitor ground terminal.
5) Connect the output power planes (V
CORE
and system
ground planes) directly to the output filter capacitor
positive and negative terminals with multiple vias.
Place the entire DC-DC converter circuit as close to
the CPU as is practical.
M
High-Speed, Digitally Adjusted
Step-Down Controllers for Notebook CPUs
26
______________________________________________________________________________________
相關PDF資料
PDF描述
MAX171 12 Bits ADC(光隔離，串行輸出,12位ADC)
MAX1720 Switched Capacitor Voltage Inverter with Shutdown(帶關斷功能的開關電容電壓反相器)
MAX173 Complete 5μs CMOS 12Bits ADC(CMOS，5μs,單通道，10位ADC)
MAX174 12 Bits ADC(工業標準，單通道，12位ADC)
MAX176 Serial Output 12 Bits ADC(串行輸出，250ksps,串行，12位ADC)
相關代理商/技術參數
參數描述
MAX17120ETJ+ 功能描述:LCD 驅動器 Triple Scan Driver for TFT LCD RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
MAX17120ETJ+T 功能描述:LCD 驅動器 Triple Scan Driver for TFT LCD RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
MAX17120EVKIT+ 功能描述:電源管理IC開發工具 MAX17120 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
MAX17121ETG+ 功能描述:LCD 驅動器 Dual Scan Driver for TFT LCD RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
MAX17121ETG+T 功能描述:LCD 驅動器 Dual Scan Driver for TFT LCD RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*