- 您現在的位置：買賣IC網 > PDF目錄2086 > MAX1185ECM+D (Maxim Integrated Products)IC ADC 10BIT 20MSPS DUAL 48-TQFP PDF資料下載
參數資料
| 型號： | MAX1185ECM+D |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 20MSPS DUAL 48-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 250 |
| 位數： | 10 |
| 采樣率（每秒）： | 20M |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 2.43W |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP 裸露焊盤 |
| 供應商設備封裝： | 48-TQFP 裸露焊盤（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 4 個單端，單極；4 個單端，雙極；2 個差分，單極；2 個差分，雙極 |
| 產品目錄頁面： | 1396 (CN2011-ZH PDF) |
MAX1185
Dual 10-Bit, 20Msps, 3V, Low-Power ADC with
Internal Reference and Multiplexed Parallel Outputs
14
______________________________________________________________________________________
Table 1. MAX1185 Output Codes For Differential Inputs
*
VREF = VREFP - VREFN
DIFFERENTIAL INPUT
VOLTAGE*
DIFFERENTIAL
INPUT
STRAIGHT OFFSET
BINARY
T/B = 0
TWO’S COMPLEMENT
T/B = 1
VREF x 511/512
+FULL SCALE - 1LSB
11 1111 1111
01 1111 1111
VREF x 1/512
+ 1 LSB
00 0000 0001
0
Bipolar Zero
10 0000 0000
00 0000 0000
- VREF x 1/512
- 1 LSB
01 1111 1111
11 1111 1111
-VREF x 511/512
- FULL SCALE + 1 LSB
00 0000 0001
10 0000 0001
-VREF x 512/512
- FULL SCALE
00 0000 0000
10 0000 0000
Single-Ended AC-Coupled Input Signal
Figure 7 shows an AC-coupled, single-ended applica-
tion. Amplifiers like the MAX4108 provide high speed,
high bandwidth, low noise, and low distortion to maintain
the integrity of the input signal.
Typical QAM Demodulation Application
The most frequently used modulation technique for digital
communications applications is probably the Quadrature
Amplitude Modulation (QAM). Typically found in spread-
spectrum based systems, a QAM signal represents a
carrier frequency modulated in both amplitude and
phase. At the transmitter, modulating the baseband sig-
nal with quadrature outputs, a local oscillator followed by
subsequent up-conversion can generate the QAM signal.
The result is an in-phase (I) and a quadrature (Q) carrier
component, where the Q component is 90 degree phase-
shifted with respect to the in-phase component. At the
receiver, the QAM signal is divided down into it’s I and Q
components, essentially representing the modulation
process reversed. Figure 8 displays the demodulation
process performed in the analog domain, using the dual
matched 3.3V, 10-bit ADC MAX1185 and the MAX2451
quadrature demodulator to recover and digitize the I and
Q baseband signals. Before being digitized by the
MAX1185, the mixed down-signal components may be fil-
tered by matched analog filters, such as Nyquist or
Pulse-Shaping filters. These remove any unwanted
images from the mixing process, thereby enhancing the
overall signal-to-noise (SNR) performance and minimizing
intersymbol interference.
Grounding, Bypassing, and
Board Layout
The MAX1185 requires high-speed board layout design
techniques. Locate all bypass capacitors as close as
possible to the device, preferably on the same side as
the ADC, using surface-mount devices for minimum
inductance. Bypass VDD, REFP, REFN, and COM with
two parallel 0.1F ceramic capacitors and a 2.2F
bipolar capacitor to GND. Follow the same rules to
bypass the digital supply (OVDD) to OGND. Multilayer
boards with separated ground and power planes pro-
duce the highest level of signal integrity. Consider the
use of a split ground plane arranged to match the
physical location of the analog ground (GND) and the
digital output driver ground (OGND) on the ADC’s
package. The two ground planes should be joined at a
single point such that the noisy digital ground currents
do not interfere with the analog ground plane. The ideal
location of this connection can be determined experi-
mentally at a point along the gap between the two
ground planes, which produces optimum results. Make
this connection with a low-value, surface-mount resistor
(1Ω to 5Ω), a ferrite bead, or a direct short. Alternatively,
all ground pins could share the same ground plane, if
the ground plane is sufficiently isolated from any noisy
digital systems ground plane (e.g., downstream output
buffer or DSP ground plane). Route high-speed digital
signal traces away from the sensitive analog traces of
either channel. Make sure to isolate the analog input
lines to each respective converter to minimize channel-
to-channel crosstalk. Keep all signal lines short and
free of 90 degree turns.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1188AEUP+ | IC ADC 16BIT 135KSPS 20-TSSOP |
| MAX1193ETI+ | IC ADC 8BIT 45MSPS DUAL 28-TQFN |
| MAX1196ECM+TD | IC ADC 8BIT 40MSPS DL 48-TQFP |
| MAX1198ECM+TD | IC ADC 8BIT 100MSPS DL 48-TQFP |
| MAX1204AEPP+ | IC ADC 10BIT 8CH 20-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1185ECM-T | 制造商:Maxim Integrated Products 功能描述:DUAL, 10-BIT, 20MSPS, +3V, LOW-POWER ADC W/ I - Tape and Reel |
| MAX1185ECM-TD | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1186ECM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1186ECM+D | 功能描述:模數轉換器 - ADC 10-Bit 2Ch 40Msps High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1186ECM+TD | 功能描述:模數轉換器 - ADC 10-Bit 2Ch 40Msps High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。