參數資料
型號： MAX11359AETL+T
廠商： Maxim Integrated Products
文件頁數： 37/67頁
文件大?。?/td> 0K
描述： IC DAS SYSTEM 16BIT 40-TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
類型： 數據采集系統（DAS）
分辨率（位）： 16 b
采樣率（每秒）： 512
數據接口： MICROWIRE?，QSPI?，串行，SPI?
電壓電源： 模擬和數字
電源電壓： 1.8 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 40-WFQFN 裸露焊盤
供應商設備封裝： 40-TQFN-EP（6x6）
包裝： 帶卷 (TR)
MAX11359A
16-Bit Data-Acquisition System with ADC, DAC,
UPIOs, RTC, Voltage Monitors, and Temp Sensor
42
Maxim Integrated
HFCE: High-frequency-clock enable bit. Set HFCE = 1
to enable the internal high-frequency clock source, and
set HFCE = 0 to disable the high-frequency clock
source.
If HFCE = 1 and CLKE = 1, the internal high-frequency
oscillator is enabled and is present at CLK. The power-
on default state is 1.
CKSEL<2:0>: Clock selection bits. These bits select
the FLL-based output clock frequency at the high-fre-
quency CLK pin as shown in Table 12. The power-on
default state is 001.
IO32E: Input/output 32kHz clock select bit. Set IO32E
= 0 to configure the CLK32K pin as an output, and set
IO32E = 1 to configure the CLK32K pin as an input,
regardless of the signal on the 32KIN pin as shown in
Table 13.
External clock frequencies applied to CLK32K are
clock sources to the FLL, charge pump, and the signal-
detect comparator. The default power-on state is 0.
CK32E: CLK32K output-buffer enable bit. Set CK32E =
1 to enable the CLK32K output buffer as long as OSCE
= 1 and IO32E = 0; otherwise the CK32E bit will not be
asserted. Set CK32E = 0 to disable the CLK32K output
buffer. The power-on default state is 1.
CLKE: CLK output-buffer enable bit. Set CLKE = 1 to
enable the CLK output buffer. Set CLKE = 0 to disable
the buffer. Disabling the buffer is useful for saving
power in cases where the high-frequency clock is used
internally but is not needed externally. If HFCE = 0, or if
CLKE = 0, CLK remains low. The power-on default
state is 1.
INTP: Interrupt pin polarity bit. Set INTP = 1 to make
INT an active-high output when asserted, and set INTP
= 0 to make INT an active-low output when asserted.
The power-on default state is 1.
WDE: Watchdog-enable bit. Set WDE = 1 to enable the
watchdog timer, which asserts
RESET low within 500ms
if the WATCHDOG register is not written. Set WDE = 0
to disable the watchdog timer. The power-on default
state is 0.
CLK32K
IO32E
32KIN, 32KOUT
RTC, PWM, WDT
CLOCK SOURCE
FLL, C/P, SDC INPUT
SOURCE
ADC CLOCK SOURCE
Output
1
0
XTAL attached
XTAL
FLL/HFCLK
Input
0
1
XTAL attached
XTAL
CLK32K
FLL/HFCLK
Table 13. Configuring the CLK32K as an Input or Output
CLOCK FREQUENCY
(kHz)
CKSEL2
CKSEL1
CKSEL0
4915.2
0
2457.6
0
1
1228.8
0
1
0
614.4
0
1
32.768
1
0
16.384
1
0
1
8.192
1
0
4.096
1
Table 12. Setting the CLK Frequency
相關PDF資料
PDF描述
MAX115CAX+ IC DAS SYSTEM 12BIT 36-SSOP
MAX1221BETX+T IC ADC/DAC 12BIT W/FIFO 36TQFNEP
MAX1257BETM+T IC ADC/DAC 12BIT 48-TQFN
MAX125CCAX+D IC DAS 14BIT 2X4CH 36-SSOP
MAX1271AENG+ IC ADC 12BIT 8CH 24-DIP
相關代理商/技術參數
參數描述
MAX1135BCAP 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1135BCAP+ 功能描述:模數轉換器 - ADC 16-Bit 150ksps 3.3V Single Supply RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1135BCAP+T 功能描述:模數轉換器 - ADC 16-Bit 150ksps 3.3V Single Supply RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1135BCAP-T 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX1135BEAP 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*