- 您現在的位置：買賣IC網 > PDF目錄9839 > MAX1134BEAP+T (Maxim Integrated Products)IC ADC 16BIT 150KSPS 20-SSOP PDF資料下載
參數資料
| 型號： | MAX1134BEAP+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/18頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 150KSPS 20-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 位數： | 16 |
| 采樣率（每秒）： | 150k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 26.4mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，單極；1 個單端，雙極 |
MAX1134/MAX1135
Detailed Description
The MAX1134/MAX1135 ADCs use a successive-
approximation technique and input track/hold (T/H) cir-
cuitry to convert an analog signal to a 16-bit digital
output. The MAX1134/MAX1135 easily interface to
microprocessors (Ps). The data bits can be read either
during the conversion in external clock mode or after the
conversion in internal clock mode.
In addition to a 16-bit ADC, the MAX1134/MAX1135
include an input scaler, an internal digital microcontroller,
calibration circuitry, and an internal clock generator.
The input scaler for the MAX1134 enables conversion
of input signals ranging from 0 to +6V (unipolar input)
or
±6V (bipolar input). The MAX1135 accepts 0 to
+2.048V (unipolar input) or
±2.048V (bipolar input). The
input range is software selectable.
Calibration
To minimize linearity, offset, and gain errors, the
MAX1134/MAX1135 have on-demand software calibra-
tion. Initiate calibration by writing a control byte with bit
M1 = 0 and bit M0 = 1 (Table 1). Select internal or exter-
nal clock for calibration by setting the INT/EXT bit in the
control byte. Calibrate the MAX1134/MAX1135 with the
same clock mode used for performing conversions.
Offsets resulting from synchronous noise (such as the
conversion clock) are canceled by the MAX1134/
MAX1135’s calibration circuitry. However, because the
magnitude of the offset produced by a synchronous
signal depends on the signal’s shape, recalibration
may be appropriate if the shape or relative timing of the
clock, or other digital signals change, as may occur if
more than one clock signal or frequency is used.
Input Scaler
The MAX1134/MAX1135 have an input scaler, which
allows conversion of true bipolar input voltages while
operating from a single 3.3V supply. The input scaler
attenuates and shifts the input as necessary to map the
external input range to the input range of the internal
ADC. The MAX1134 analog input range is 0 to +6V
(unipolar) or
±6V (bipolar). The MAX1135 analog input
16-Bit ADCs, 150ksps, 3.3V Single Supply
8
_______________________________________________________________________________________
BIT
NAME
DESCRIPTION
7 (MSB)
START
The first logic 1 bit after
CS goes low defines the beginning of the control byte.
6
UNI/
BIP
1 = unipolar, 0 = bipolar. Selects unipolar or bipolar conversion mode. In unipolar mode, analog input
signals from 0 to +6V (MAX1134) or 0 to +VREF (MAX1135) can be converted. In bipolar mode, analog
input signals from -6V to +6V (MAX1134) or -VREF to +VREF (MAX1135) can be converted.
5
INT/
EXT
Selects the internal or external conversion clock. 1 = internal, 0 = external.
M1
M0
Mode
0
24 external clocks per conversion (short acquisition mode)
4M1
0
1
Start calibration: starts internal calibration
1
0
Software power-down mode
3M0
1
32 external clocks per conversion (long acquisition mode)
2P2
1P1
0 (LSB)
P0
These 3 bits are stored in a port register and output to pins P2, P1, and P0 for use in addressing a mux
or PGA. These 3 bits are updated in the port register simultaneously when a new control byte is written.
Table 1. Control Byte Format
VOLTAGE
REFERENCE
BIPOLAR
UNIPOLAR
TRACK
S2
S3
S1 = BIPOLAR/UNIPOLAR
S2, S3 = T/H SWITCH
R2 = 7.6k
(MAX1134)
OR 2.5k
(MAX1135)
R3 = 3.9k
(MAX1134)
OR INFINITY (MAX1135)
HOLD
T/H OUT
CHOLD
32pF
R1
2.5k
R2
R3
AIN
TRACK
S1
Figure 1. Equivalent Input Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| V48C12M150B3 | CONVERTER MOD DC/DC 12V 150W |
| MS27467T17F26P | CONN PLUG 26POS STRAIGHT W/PINS |
| MAX13084EESA+T | IC TXRX RS485/422 ESD 8SOIC |
| MAX1135BEAP+T | IC ADC 16BIT 150KSPS 20-SSOP |
| MS27474T12A35SA | CONN RCPT 22POS JAM NUT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1135 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit ADCs.150ksps.3.3V Single Supply |
| MAX11358B | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit Data-Acquisition System with ADC, DAC, UPIOs, RTC, Voltage Monitors, and Temp Sensor |
| MAX11358BCTL+ | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:16-Bit Data-Acquisition System with ADC, DAC, UPIOs, RTC, Voltage Monitors, and Temp Sensor |
| MAX11358BETL+ | 功能描述:ADC / DAC多通道 Integrated Circuits (ICs) Analog to Digital Converters - Special Purpose - IC DAS SYSTEM 16BIT 40-TQFN RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX11358BETL+T | 功能描述:ADC / DAC多通道 Integrated Circuits (ICs) Analog to Digital Converters - Special Purpose - IC DAS SYSTEM 16BIT 40-TQFN RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
發布緊急采購，3分鐘左右您將得到回復。