- 您現在的位置：買賣IC網 > PDF目錄384648 > MAX1111EPE (MAXIM INTEGRATED PRODUCTS INC) +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs PDF資料下載
參數資料
| 型號： | MAX1111EPE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
| 中文描述： | 4-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP16 |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 15/20頁 |
| 文件大?。?/td> | 284K |
| 代理商： | MAX1111EPE |
M
+2.7V, Low-Power, Multic hannel,
S erial 8-Bit ADCs
______________________________________________________________________________________
15
SCLK
DIN
DOUT
CS
S
CONTROL BYTE 0
CONTROL BYTE 1
S
CONVERSION RESULT 0
B7 B0
B7 B0
B7
CONVERSION RESULT 1
CONVERSION RESULT 2
SSTRB
CONTROL BYTE 2
S
1
8
8
8
10
1
10
1
10 1
CONTROL BYTE 3
S
Figure 12a. Continuous Conversions, External Clock Mode, 10 Clocks/Conversion Timing
CS
SCLK
DIN
DOUT
S
CONTROL BYTE 0
CONTROL BYTE 1
S
CONVERSION RESULT 0
B7 B0
B7
CONVERSION RESULT 1
Figure 12b. Continuous Conversions, External Clock Mode, 16 Clocks/Conversion Timing
Data Framing
The falling edge of
CS
does not start a conversion. The
first logic high clocked into DIN is interpreted as a start
bit and defines the first bit of the control byte. A conver-
sion starts on the falling edge of SCLK, after the eighth
bit of the control byte (the PD0 bit) is clocked into DIN.
The start bit is defined as:
The first high bit clocked into DIN with
CS
low any
time the converter is idle; e.g., after V
DD
is applied.
OR
The first high bit clocked into DIN after the MSB of a
conversion in progress is clocked onto the DOUT
pin.
If
CS
is toggled before the current conversion is com-
plete, then the next high bit clocked into DIN is recog-
nized as a start bit; the current conversion is
terminated, and a new one is started.
The fastest the MAX1110/MAX1111 can run is 10
clocks per conversion. Figure 12a shows the serial-
interface timing necessary to perform a conversion
every 10 SCLK cycles in external clock mode.
Many microcontrollers require that conversions occur in
multiples of eight SCLK clocks; 16 clocks per conver-
sion is typically the fastest that a microcontroller can
drive the MAX1110/MAX1111. Figure 12b shows the
serial-interface timing necessary to perform a conver-
sion every 16 SCLK cycles in external clock mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1111MJE | +2.7V, Low-Power, Multichannel, Serial 8-Bit ADCs |
| MAX1115 | Single-Supply, Low-Power, Serial 8-Bit ADCs |
| MAX1115EKA | Single-Supply, Low-Power, Serial 8-Bit ADCs |
| MAX1116EKA | Single-Supply, Low-Power, Serial 8-Bit ADCs |
| MAX1117EKA | Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1111EPE+ | 功能描述:模數轉換器 - ADC 2.7V Low-Power Multi Ch Serial 8-Bit RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1111MJE | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1112 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:+5V, Low-Power, Multi-Channel, Serial 8-Bit ADCs |
| MAX11120 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1Msps, Low-Power, Serial 12-/10-/8-Bit, 4-/8-/16-Channel ADCs |
| MAX11120_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1Msps, Low-Power, Serial 12-/10-/8-Bit,4-/8-/16-Channel ADCs |
發布緊急采購，3分鐘左右您將得到回復。