- 您現(xiàn)在的位置：買賣IC網 > PDF目錄16967 > MA160014 (Microchip Technology)MOD PLUG-IN 44PIN PIC18LF45K22 PDF資料下載
參數資料
| 型號： | MA160014 |
| 廠商： | Microchip Technology |
| 文件頁數： | 37/71頁 |
| 文件大小： | 0K |
| 描述： | MOD PLUG-IN 44PIN PIC18LF45K22 |
| 標準包裝： | 1 |
| 系列： | PIC® XLP™ 18F |
| 附件類型： | 插拔式模塊（PIM）- PIC18LF45K22 |
| 適用于相關產品： | PICDEM PIC18 Explorer，DM183032 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
PIC18(L)F2X/4XK22
DS41412E-page 42
2010-2012 Microchip Technology Inc.
2.11.3
CLOCK SWITCH TIMING
When switching between one oscillator and another,
the new oscillator may not be operating which saves
power (see Figure 2-9). If this is the case, there is a
delay after the SCS<1:0> bits of the OSCCON register
are modified before the frequency change takes place.
The OSTS and IOFS bits of the OSCCON register will
reflect the current active status of the external and
HFINTOSC oscillators. The timing of a frequency
selection is as follows:
1.
SCS<1:0> bits of the OSCCON register are mod-
ified.
2.
The old clock continues to operate until the new
clock is ready.
3.
Clock switch circuitry waits for two consecutive
rising edges of the old clock after the new clock
ready signal goes true.
4.
The system clock is held low starting at the next
falling edge of the old clock.
5.
Clock switch circuitry waits for an additional two
rising edges of the new clock.
6.
On the next falling edge of the new clock the low
hold on the system clock is released and new
clock is switched in as the system clock.
7.
Clock switch is complete.
See Figure 2-1 for more details.
If the HFINTOSC is the source of both the old and new
frequency, there is no start-up delay before the new
frequency is active. This is because the old and new
frequencies are derived from the HFINTOSC via the
postscaler and multiplexer.
Start-up
delay
specifications
are
located
in
Specifications (Oscillator Module).
2.12
Two-Speed Clock Start-up Mode
Two-Speed Start-up mode provides additional power
savings by minimizing the latency between external
oscillator start-up and code execution. In applications
that make heavy use of the Sleep mode, Two-Speed
Start-up will remove the external oscillator start-up
time from the time spent awake and can reduce the
overall power consumption of the device.
This mode allows the application to wake-up from
Sleep, perform a few instructions using the HFINTOSC
as the clock source and go back to Sleep without
waiting for the primary oscillator to become stable.
When the oscillator module is configured for LP, XT or
HS modes, the Oscillator Start-up Timer (OST) is
enabled (see Section 2.5.1 “Oscillator Start-up Timer
(OST)”). The OST will suspend program execution until
1024 oscillations are counted. Two-Speed Start-up
mode minimizes the delay in code execution by
operating from the internal oscillator as the OST is
counting. When the OST count reaches 1024 and the
OSTS bit of the OSCCON register is set, program
execution switches to the external oscillator.
2.12.1
TWO-SPEED START-UP MODE
CONFIGURATION
Two-Speed Start-up mode is enabled when all of the
following settings are configured as noted:
Two-Speed Start-up mode is enabled when the
IESO of the CONFIG1H Configuration register is
set.
SCS<1:0> (of the OSCCON register) = 00.
FOSC<2:0> bits of the CONFIG1H Configuration
register are configured for LP, XT or HS mode.
Two-Speed Start-up mode becomes active after:
Power-on Reset (POR) and, if enabled, after
Power-up Timer (PWRT) has expired, or
Wake-up from Sleep.
Note:
Executing a SLEEP instruction will abort
the oscillator start-up time and will cause
the OSTS bit of the OSCCON register to
remain clear.
相關PDF資料 |
PDF描述 |
|---|---|
| 1-1589476-5 | CONN RCPT 15POS 30AWG 30IN |
| MAX1607ESA+T | IC SW USB CURRENT LIMIT 8SOIC |
| MA180023 | MODULE PLUG-IN PIC18F46J11 PIM |
| 1-1589476-8 | CONN RCPT 15POS 32AWG 24IN |
| 0210490389 | CABLE JUMPER 1.25MM .051M 32POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MA160015 | 功能描述:子卡和OEM板 PIC16LF1947 PIM RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MA160016 | 功能描述:子卡和OEM板 PIC16F1947 PIM RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MA161 | 制造商:Panasonic Industrial Company 功能描述:DIODE |
| MA16101BAN | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:HIGH FREQUENCY CERAMIC CAPACITORS |
| MA16101BBN | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:HIGH FREQUENCY CERAMIC CAPACITORS |
發(fā)布緊急采購，3分鐘左右您將得到回復。