- 您現在的位置：買賣IC網 > PDF目錄370969 > M5M28F101AFP (Mitsubishi Electric Corporation) 1048576-BIT (131072-WORD BY 8-BIT) CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | M5M28F101AFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | 1048576-BIT (131072-WORD BY 8-BIT) CMOS FLASH MEMORY |
| 中文描述： | 1048576位（131072 - Word的8位）的CMOS閃存 |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 96K |
| 代理商： | M5M28F101AFP |
MITSUBISHI LSIs
1048576-BIT (131072-WORD BY 8-BIT) CMOS FLASH MEMORY
M5M28F101AFP,J,VP,RV-85,-10
(970407)
3
When V
PP
is low (V
PP
= V
PPL
), the contents of the command latch
are fixed to 00H, and the device is in read-only mode. When V
PP
is
high (V
PP
= V
PPH
), the device enters read/write mode. The device
operations are selected by writing specific software command into
the command latch.
Read Command
The device is in read mode after writing Read Command (00H) to
the command latch. The device continues to be in read mode until
the other commands are written. When V
PP
powers-up to high
voltage (V
PP
= V
PPH
), the default contents of the command latch is
00H. So it is ensured that the false alteration of memory data does
not occur during V
PP
power transition.
Program Command
Program Command is the command for byte-program, and
program is initiated by twice of write cycles. Program Command
(40H) is written to the command latch in first write cycle, and the
address and data to be programmed are latched in second write
cycle. Then the address and data are latched on the falling edge
and the rising edge of WE pulse, respectively. The byte- program
operation is initiated at the rising edge of WE in second write
cycle, and terminates in 10 μs, controlled by the internal timer.
Program Verify Command
Following byte program, the programmed byte must be verified.
The program-verify is initiated by writing Program Verify Command
(C0H) to the command latch. After writing Program Verify
Command, programmed data is verified in read mode. Then the
address information is not needed.
Auto Program Command
Auto Program Command is the command for automated program
and program-verify of one byte, and Auto Program is initiated by
twice of write cycles.
Auto Program Command (10H or 50H) is written to the command
latch in first write cycle, and the address and data to be
programmed are latched in second write cycle. Then the address
and data are latched on the falling edge and the rising edge of WE
pulse, respectively. The program operation is initiated at the rising
edge of WE in second write cycle, and program-verify begin auto-
matically. So it is not necessary to program-verify mode after this.
And the complete of Auto Program can be indicated by data
polling.
Data polling is the indication of the complete of Auto Program.
During the Auto Program, on WE=V
IH
and CE=OE=V
IL
, the data of
D
0~
D
7
are the inverse of written datum. When Auto Program is
completed, the written datum will be output. It is necessary to fix
the address of written byte during data polling.
Erase Command
Erase Command is the command for chip-erase, and chip-erase is
initiated by writing twice of the Erase Command (20H)
consecutively to the command latch. The erase operation is
initiated with the rising edge of the WE pulse and terminates in
9.5ms, controlled by the internal timer. This two-step sequence for
chip-erase prevents from erasing accidentally.
Erase Verify Command
Following each erase, all bytes must be verified. The erase verify
is initiated by writing Erase Verify Command (A0H) to the
command latch, while the address to be verified is latched on the
falling edge of the WE pulse. The erase verify command must be
written to the command latch and each address is latched before
each byte is verified. The operation continues for each byte until a
byte is not erased, or the last address is accessed.
Auto Erase Command
Auto Erase Command is the command for automated erase and
erase-verify of all bytes, and Auto Erase is initiated by twice of the
Erase Command (30H) consecutively to the command latch. First,
the preprogram operation is initiated at the rising edge of WE in
second write cycle, and so all byte become zero data. Second,
erase and erase-verify begin, automatically. So it is not necessary
to preprogram and erase-verify mode. And the complete of Auto
Erase can be indicated by status polling.
Status polling is the indication of the complete of Auto Erase.
During the Auto Erase, on WE=V
IH
and CE=OE=V
IL
, the data of
D
7
is "0". When Auto Erase is completed, the data of D
7
is "1".
(D
0~
D
7
are "FFH". )
Reset Command
Reset Command is the command to safely abort the erase or
program sequences. Following erase or program command in first
write cycle, the operation is aborted safely by writing the two
consecutive Reset Commands (FFH). Then the device enters read
mode without altering memory contents.
Read Device Identifier Code
Device Identifier operation is initiated by writing 80H into the
command latch. Following the command write, the manufacturer
code (1CH) and the device code (D9H) can be read from address-
00000H and 00001H, respectively.
The M5M28F101A is supported with the Common Device
Identifier Code of MITSUBISHI 1M Flash memory (x8) family.
Common Device Identifier operation is initiated by writing 90H into
the command latch. Under this case, following the command write,
the manufacturer code (1CH) and the device code (D0H) can be
read from address-00000H and 00001H, respectively. Additionally,
Common Device Identifier operation is initiated by rising A
9
to high
voltage for PROM programmers.
SOFTWARE COMMAND
相關PDF資料 |
PDF描述 |
|---|---|
| M5M29FB800FP | 8,388,608-BIT (1048,576-576-WORD BY 8-BIT / 524,288-WORD BY16-BIT)CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY |
| M5M29FB800VP | 8,388,608-BIT (1048,576-576-WORD BY 8-BIT / 524,288-WORD BY16-BIT)CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY |
| M5M29FB800RV-10 | 8,388,608-BIT (1048,576-576-WORD BY 8-BIT / 524,288-WORD BY16-BIT)CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY |
| M5M29FT800RV-10 | 8,388,608-BIT (1048,576-576-WORD BY 8-BIT / 524,288-WORD BY16-BIT)CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY |
| M5M29FB800RV-12 | 8,388,608-BIT (1048,576-576-WORD BY 8-BIT / 524,288-WORD BY16-BIT)CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M5M28F101J12 | 制造商:MITS 功能描述:28F010-120 S8H2A |
| M5M28F101J-12 | 制造商:MITS 功能描述:28F010-120 S8H2A |
| M5M28F101J-15 | 制造商:Mitsubishi Electric 功能描述: |
| M5M29F25611VP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:MORE THAN 16,057 SECTORS (271,299,072 BITS) CMOS 3.3V-ONLY SERIAL READ FLASH MEMORY |
| M5M29FB800FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:8,388,608-BIT (1048,576-576-WORD BY 8-BIT / 524,288-WORD BY16-BIT)CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY |
發(fā)布緊急采購，3分鐘左右您將得到回復。