參數資料
型號: M48T86MH1E
廠商: STMICROELECTRONICS
元件分類: 時鐘/數據恢復及定時提取
英文描述: 1 TIMER(S), REAL TIME CLOCK, PDSO28
封裝: 0.330 INCH, ROHS COMPLIANT, PLASTIC, SOH-28
文件頁數: 6/36頁
文件大?。?/td> 352K
代理商: M48T86MH1E
Obsolete
Product(s)
- Obsolete
Product(s)
Clock operations
M48T86
3
Clock operations
3.1
Address map
The address map of the M48T86 is shown in Figure 8. It consists of 114 bytes of user RAM,
10 bytes of RAM that contain the RTC time, calendar and alarm data, and 4 bytes which are
used for control and status. All bytes can be read or written to except for the following:
1.
Registers C & D are “Read only.”
2.
Bit 7 of Register A is “Read only.”
The contents of the four Registers A, B, C, and D are described in the “Registers” section.
3.2
Time, calendar, and alarm locations
The time and calendar information is obtained by reading the appropriate memory bytes.
The time, calendar, and alarm registers are set or initialized by writing the appropriate RAM
bytes. the contents of the time, calendar, and alarm bytes can be either binary or binary-
coded decimal (BCD) format. Before writing the internal time, calendar, and alarm register,
the SET bit (Register B; Bit 7) should be written to a logic '1.' This will prevent updates from
occurring while access is being attempted. In addition to writing the time, calendar, and
alarm registers in a selected format (binary or BCD), the data mode (DM) bit (Register B; Bit
2), must be set to the appropriate logic level ('1' signifies binary data; '0' signifies binary
coded decimal (BCD data). All time, calendar, and alarm bytes must use the same data
mode. The SET bit should be cleared after the data mode bit has been written to allow the
real-time clock to update the time and calendar bytes. Once initialized, the real-time clock
makes all updates in the selected mode. The data mode cannot be changed without
reinitializing the ten data bytes. Table3 on page15 shows the binary and BCD formats of
the time, calendar, and alarm locations. The 24/12 bit (Register B; Bit 1) cannot be changed
without reinitializing the hour locations. When the 12-hour format is selected, a logic '1' in
the high order bit of the hours byte represents PM. The time, calendar, and alarm bytes are
always accessible because they are double-buffered. Once per second the ten bytes are
advanced by one second and checked for an alarm condition. If a READ of the time and
calendar data occurs during an update, a problem exists where data such as seconds,
minutes, or hours may not correlate. However, the probability of reading incorrect time and
calendar data is low. Methods of avoiding possible incorrect time and calendar READs are
reviewed later in this text.
相關PDF資料
PDF描述
M4T32-BR12SH1 1 TIMER(S), REAL TIME CLOCK, DSS4
M50734FP-10 8-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP72
M50734SP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64
M50930-XXXFP 8-BIT, MROM, 4.3 MHz, MICROCONTROLLER, PQFP80
M50931-XXXFP 8-BIT, MROM, 4.3 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
M48T86MH1F 功能描述:實時時鐘 5 Volt PC Drop-In RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M48T86MH1TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5.0 V PC real-time clock
M48T86PC 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5V PC REAL TIME CLOCK
M48T86PC1 功能描述:實時時鐘 5 Volt PC Drop-In RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M48T86PC1 制造商:STMicroelectronics 功能描述:IC - Real Time Clock