- 您現在的位置：買賣IC網 > PDF目錄45048 > M38C24M4-XXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M38C24M4-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64 |
| 文件頁數： | 21/91頁 |
| 文件大?。?/td> | 1867K |
| 代理商： | M38C24M4-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁
27
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
Fig. 22 Waveform of PWM/IGBT
(5) Event Counter Mode
The timer counts signals input through the CNTR0 pin. In this mode,
timer X operates as the 18-bit counter by setting the timer X register
(extension). When using this mode, set the port sharing the CNTR0
pin to input mode.
In this mode, the window control can be performed by the timer 1
underflow. When the bit 5 (data for control of event counter window)
of the timer X mode register is set to “1”, counting is stopped at the
next timer 1 underflow. When the bit is set to “0”, counting is re-
started at the next timer 1 underflow.
(6) Pulse Width Measurement Mode
In this mode, the count source is the output of frequency divider for
timer. In this mode, timer X operates as the 18-bit counter by setting
the timer X register (extension). When the bit 6 of the CNTR0 active
edge switch bits is “0”, counting is executed during the “H” interval of
CNTR0 pin input. When the bit is “1”, counting is executed during the
“L” interval of CNTR0 pin input. When using this mode, set the port
sharing the CNTR0 pin to input mode.
s Notes on Timer X
(1) Write Order to Timer X
In the timer mode, pulse output mode, event counter mode and
pulse width measurement mode, write to the following registers in
the order as shown below;
the timer X register (extension),
the timer X register (low-order),
the timer X register (high-order).
Do not write to only one of them.
When the above mode is set and timer X operates as the 16-bit
counter, if the timer X register (extension) is never set after reset is
released, setting the timer X register (extension) is not required. In
this case, write the timer X register (low-order) first and the timer X
register (high-order). However, once writing to the timer X register
is executed, note that the value is retained to the reload latch.
In the IGBT and PWM modes, do not write “1” to the timer X register
(extension). Also, when “1” is already written to the timer X register,
be sure to write “0” to the register before using.
Write to the following registers in the order as shown below;
the compare register (high- and low-order),
the timer X register (extension),
the timer X register (low-order),
the timer X register (high-order).
It is possible to use whichever order to write to the compare regis-
ter (high- and low-order). However, write both the compare register
and the timer X register at the same time.
(2) Read Order to Timer X
In all modes, read the following registers in the order as shown below;
the timer X register (extension),
the timer X register (high-order),
the timer X register (low-order).
When reading the timer X register (extension) is not required, read
the timer X register (high-order) first and the timer X register (low-
order).
Read order to the compare register is not specified.
If reading to the timer X register during write operation or writing to
it during read operation is performed, normal operation will not be
performed.
(3) Write to Timer X
When writing a value to the timer X address to write to the latch
only, the value is set into the reload latch and the timer is updated
at the next underflow. Normally, when writing a value to the timer X
address, the value is set into the timer and the timer latch at the
same time, because they are written at the same time.
When writing to the latch only, if the write timing to the high-order
reload latch and the underflow timing are almost the same, the value
is set into the timer and the timer latch at the same time. In this time,
counting is stopped during writing to the high-order reload latch.
Do not switch the timer count source during timer count operation.
Stop the timer count before switching it.
ts
Timer X count
source
Timer X
PWM mode
IGBT mode
(n-m+1) tsm ts
(n+1) ts
When the Timer X setting value = n and the compare register setting value = m,
the following PWM waveform is output;
Duty : (n-m+1)/(n+1)
Period : (n+1) ts (ts: period of timer X count source)
相關PDF資料 |
PDF描述 |
|---|---|
| M38C29MC-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C29MC-XXXFP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C29FFFP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C29FFHP | 8-BIT, FLASH, 4 MHz, MICROCONTROLLER, PQFP64 |
| M38C34M6AXXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38C24M4-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-051HP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C24M6-XXXHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38C29FFAFP | 制造商:Renesas Electronics Corporation 功能描述: |
發(fā)布緊急采購，3分鐘左右您將得到回復。