- 您現在的位置：買賣IC網 > PDF目錄45046 > M38507F8FP 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDSO42 PDF資料下載
參數資料
| 型號： | M38507F8FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDSO42 |
| 封裝： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件頁數： | 54/99頁 |
| 文件大?。?/td> | 1419K |
| 代理商： | M38507F8FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
58
3850 Group (Spec. H/A)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Symbol
Table 13 Definition of each bit in status register (SRD)
Status Register (SRD)
The status register shows the operating status of the flash
memory and whether erase operations and programs ended suc-
cessfully or in error. It can be read in the following ways:
(1) By reading an arbitrary address from the User ROM area after
writing the read status register command (7016)
(2) By reading an arbitrary address from the User ROM area in the
period from when the program starts or erase operation starts
to when the read array command (FF16) is input.
Also, the status register can be cleared by writing the clear status
register command (5016).
After reset, the status register is set to “8016”.
Table 13 shows the status register. Each bit in this register is ex-
plained below.
Sequencer status (SR7)
The sequencer status indicates the operating status of the flash
memory. This bit is set to “0” (busy) during write or erase operation
and is set to “1” when these operations ends.
After power-on, the sequencer status is set to “1” (ready).
Erase status (SR5)
The erase status indicates the operating status of erase operation.
If an erase error occurs, it is set to “1”. When the erase status is
cleared, it is set to “0”.
Program status (SR4)
The program status indicates the operating status of write opera-
tion. When a write error occurs, it is set to “1”.
The program status is set to “0” when it is cleared.
If “1” is written for any of the SR5 and SR4 bits, the program,
erase all blocks, and block erase commands are not accepted.
Before executing these commands, execute the clear status regis-
ter command (5016) and clear the status register.
Also, if any commands are not correct, both SR5 and SR4 are set
to “1”.
SR7 (bit7)
SR6 (bit6)
SR5 (bit5)
SR4 (bit4)
SR3 (bit3)
SR2 (bit2)
SR1 (bit1)
SR0 (bit0)
Definition
“1”
“0”
Status name
Sequencer status
Reserved
Erase status
Program status
Reserved
Ready
-
Terminated in error
-
Busy
-
Terminated normally
-
相關PDF資料 |
PDF描述 |
|---|---|
| M38504E6-XXXSP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| M38507M8A-XXXSP | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDIP42 |
| M38504M6A-XXXFP | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42 |
| M38503M4A-XXXSP | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDIP42 |
| M38503M4A-XXXFP | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38507F8FP#U1 | 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays |
| M38507F8FP#W1 | 制造商:Renesas Electronics Corporation 功能描述:FLASH 8-BIT 2.7 TO 5.5V PBFREE |
| M38507F8FP(#U1) | 制造商:Renesas Electronics Corporation 功能描述: |
| M3851 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 7COND 14AWG BLK 1000' |
| M3851 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 7COND 14AWG BLK 500' |
發布緊急采購，3分鐘左右您將得到回復。