參數資料
型號: M38507F8FP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 12.5 MHz, MICROCONTROLLER, PDSO42
封裝: 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42
文件頁數: 48/99頁
文件大?。?/td> 1419K
代理商: M38507F8FP
52
3850 Group (Spec. H/A)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Fig. 57 Block diagram of built-in flash memory
(1) CPU Rewrite Mode
In CPU rewrite mode, the internal flash memory can be operated
on (read, program, or erase) under control of the Central Process-
ing Unit (CPU).
In CPU rewrite mode, only the User ROM area shown in Figure 57
can be rewritten; the Boot ROM area cannot be rewritten. Make
sure the program and block erase commands are issued for only
the User ROM area and each block area.
The control program for CPU rewrite mode can be stored in either
User ROM or Boot ROM area. In the CPU rewrite mode, because
the flash memory cannot be read from the CPU, the rewrite con-
trol program must be transferred to internal RAM area to be
executed before it can be executed.
Microcomputer Mode and Boot Mode
The control program for CPU rewrite mode must be written into
the User ROM or Boot ROM area in parallel I/O mode beforehand.
(If the control program is written into the Boot ROM area, the stan-
dard serial I/O mode becomes unusable.)
See Figure 57 for details about the Boot ROM area.
Normal microcomputer mode is entered when the microcomputer
is reset with pulling CNVSS pin low. In this case, the CPU starts
operating using the control program in the User ROM area.
When the microcomputer is reset by pulling the P41/INT0 pin high,
the CNVss pin high, the CPU starts operating using the control
program in the Boot ROM area (program start address is FFFC16,
FFFD16 fixation). This mode is called the “Boot” mode.
Block Address
Block addresses refer to the maximum address of each block.
These addresses are used in the block erase command. In case
of the M38507F8, it has only one block.
800016
Block 1 : 32 kbyte
User ROM area
4 kbyte
F00016
FFFF16
Boot ROM area
Notes 1: The Boot ROM area can be rewritten in only parallel
input/output mode. (Access to any other areas is inhibited.)
2: To specify a block, use the maximum address in the block.
Product name
Flash memory
start address
M38507F8800016
Parallel I/O mode
800016
Block 1 : 32 kbyte
FFFF16
CPU rewrite mode, standard serial I/O mode
User ROM area
4 kbyte
F00016
FFFF16
Boot ROM area
BSEL = 0
BSEL = 1
User area / Boot area selection bit = 0
User area / Boot area selection bit = 1
相關PDF資料
PDF描述
M38504E6-XXXSP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP42
M38507M8A-XXXSP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDIP42
M38504M6A-XXXFP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42
M38503M4A-XXXSP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDIP42
M38503M4A-XXXFP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42
相關代理商/技術參數
參數描述
M38507F8FP#U1 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays
M38507F8FP#W1 制造商:Renesas Electronics Corporation 功能描述:FLASH 8-BIT 2.7 TO 5.5V PBFREE
M38507F8FP(#U1) 制造商:Renesas Electronics Corporation 功能描述:
M3851 BK001 制造商:Alpha Wire Company 功能描述:CBL 7COND 14AWG BLK 1000'
M3851 BK002 制造商:Alpha Wire Company 功能描述:CBL 7COND 14AWG BLK 500'