- 您現在的位置：買賣IC網 > PDF目錄370846 > M37540E8GP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M37540E8GP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 21/64頁 |
| 文件大?。?/td> | 668K |
| 代理商： | M37540E8GP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7540 Group
MITSUBISHI MICROCOMPUTERS
21
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
G
Timer Z
Timer Z is an 8-bit timer and can be selected in one of 4 operating
modes by setting the timer YZ mode register (TYZM).
Timer mode
Programmable waveform generation mode
Programmable one-shot generation mode
Programmable wait one-shot generation mode
The division ratio of timer Z and prescaler Z is 1/(n+1) provided that
the value of the timer Z latch or prescaler Z latch is n.
(1)Timer mode
Mode select
Timer mode is selected by setting timer Z operation mode bits
(b5,b4) of TYZM to “00”.
Count source select
The count source is f(X
IN
)/2, f(X
IN
)/16 or timer Y underflow.
Interrupt
When an underflow occurs, timer Z interrupt request bit (b1) of
IREQ2 is set to “1”.
Operation description
After reset release, timer Z is operating because the timer Z count
stop bit (b7) is “0”. Timer operation is stopped by setting b7 of
TYZM to “1”. In the timer mode, the timer count value is set by
timer Z primary latch (TZP). When a value is set to TZP while timer
is stopped, the setting value is written to latch and timer simulta-
neously.
When timer Z reaches “00”, an underflow occurs at the next count
pulse, and the timer Z latch is reloaded into the timer and count
continues. When timer value is changed during the count opera-
tion, either “writing to latch and timer simultaneously” or “writing to
only latch” can be selected by setting the timer Z write control bit
(b6) of TYZM. When selecting “writing to only latch”, the timer count
value is changed after the next underflow.
(2)Programmable waveform generation mode
Mode select
Timer mode is selected by setting timer Z operation mode bits
(b5,b4) of TYZM to “01”.
When this mode is selected, set timer Z write control bit (b6) of
TYZM to “1” (“writing to only latch” selected).
Count source select
The count source is f(X
IN
)/2, f(X
IN
)/16 or timer Y underflow.
Interrupt
When an underflow occurs, timer Z interrupt request bit (b1) of
IREQ is set to “1”.
Operation description
After reset release, timer Z is operating because the timer Z count
stop bit (b7) of TYZM is “0”. MCU operates in the programmable
waveform generation mode when timer Z operation mode bits (b5,
b4) of TYZM is set to “01” and b7 to “0” after timer Z operation is
stopped by setting b7 of TYZM to “1”.
In the programmable waveform generation mode, timer counts the
setting value of timer Z primary latch (TZP) and the setting value
of timer Z secondary latch (TZS) alternately, the waveform inverted
each time TZP and TZS underflow is output from TZ
OUT
pin. The
active edge of output waveform is set by the timer Z output level
latch (b5) of the timer Y, Z waveform output control register (PUM).
When “0” is set to b5 of PUM, the initial state of timer at stop is “L”,
and “H” interval by the setting value of TZP or “L” interval by the
setting value of TZS is output alternately. When “1” is set to b5 of
PUM, the initial state of timer at stop is “H”, and “L” interval by the
setting value of TZP or “H” interval by the setting value of TZS is
output alternately.
Also, in this mode, the primary interval and the secondary interval
of the output waveform can be extended respectively for 0.5 cycle
of timer count source clock by setting the timer Z primary wave-
form extension control bit (b2) and the timer Z secondary wave-
form extension control bit (b3) of PUM to “1”. As a result, the wave-
forms of more accurate resolution can be output.
When b2 and b3 of PUM are used, the frequency and duty of the
output waveform are as follows;
Waveform frequency:
FTZOUT = (2
TMCL)/(2
(TZP + 1)+2
(TZS) + (EXPZP + EXPZS))
Duty:
DTZOUT = (2
(TZP + 1)) + EXPZP)/(2
(TZS+1) + EXPZS))
TMCL: Timer Z count clock f(X
IN
)/2 or f(X
IN
)/16
TZP: Timer Z primary latch (8 bits)
TZS: Timer Z secondary latch (8 bits)
EXPZP: Timer Z primary waveform extension control bit (1 bit)
EXPZS: Timer Z secondary waveform extension control bit (1 bit)
When using the programmable waveform generation mode, note
the following;
Notes on using the programmable waveform generation mode
When setting and changing TZP, TZS, EXPZP and EXPZS, write
to TZP at last because the setting to them is executed all at once
by writing to TZP. Even when TZP is not changed, write the same
value. The value is reloaded to timer at the beginning of the next
primary interval.
Set by software in order not to execute the writing to timer Z pri-
mary and the timing of timer underflow simultaneously. When read-
ing the timer Z secondary, the undefined value is read out. How-
ever, while timer counts the setting value of the timer Z secondary,
the count values at the secondary interval can be identified by
reading the timer Z primary.
In this mode, set port P0
2
which is also used as TZ
OUT
pin to out-
put.
B2 and b3 of PUM can be used only when “00
16
” is set to prescaler
Z and f(X
IN
)/2 or f(X
IN
)/16 is selected as the timer Z count source.
相關PDF資料 |
PDF描述 |
|---|---|
| M37540E8SP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540M4 | CABLE ASSEMBLY; 7/16" MALE TO 7/16" MALE; 50 OHM, RG218/U COAX; 48" CABLE LENGTH |
| M37540M4-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540M4-XXXGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540M4T-XXXGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37540E8GP#U0 | 功能描述:IC 7540 MCU OTP 32K 32LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M37540E8SP | 制造商:Renesas Electronics Corporation 功能描述: |
| M37540E8T-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540E8T-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES |
| M37540E8V-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。