- 您現在的位置：買賣IC網 > PDF目錄370846 > M37540 (Mitsubishi Electric Corporation) Single Chip 8 Bits CMOS Microcomputer(8位單片機) PDF資料下載
參數資料
| 型號： | M37540 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 8 Bits CMOS Microcomputer(8位單片機) |
| 中文描述： | 單芯片的CMOS 8位單片機（8位單片機） |
| 文件頁數： | 22/64頁 |
| 文件大?。?/td> | 668K |
| 代理商： | M37540 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7540 Group
MITSUBISHI MICROCOMPUTERS
22
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
(3)Programmable one-shot generation mode
Mode select
Timer mode is selected by setting timer Z operation mode bits
(b5,b4) of TYZM to “10”.
When this mode is selected, set timer Z write control bit (b6) of
TYZM to “1” (“writing to only latch” selected).
Count source select
The count source is f(X
IN
)/2, f(X
IN
)/16 or timer Y underflow.
Interrupt
When an underflow occurs, timer Z interrupt request bit (b1) of
IREQ2 is set to “1”.
Operation description
After reset release, timer Z is operating because the timer Z count
stop bit (b7) of TYZM is “0”. MCU operates in the programmable
one-shot generation mode when timer Z operation mode bits (b5,
b4) of TYZM is set to “10” after timer Z operation is stopped by
setting b7 of TYZM to “1”.
Timer Z is enabled to accept the one-shot start trigger when “0” is
written to b7 of TYZM after the timer count value is set to the timer
Z primary latch (TZP). In this state, when “1” is written to the timer
Z one-shot start bit (b0) of the one-shot start register (ONS), timer
Z starts count operation, at the same time, the output of TZ
OUT
pin
is inverted. Timer Z counts down the value of TZP and stops after
the output of TZ
OUT
pin is inverted to the same level as the initial
state when an underflow occurs. In this time, the next one-shot
pulse can be output by writing b0 of ONS to “1” because this bit is
initialized to “0”.
The active edge of the output waveform from TZ
OUT
pin is set by
the timer Z output level latch (b5) of PUM. When “0” is set to b5 of
PUM, the initial level of timer at stop is “L” and “H” is output at the
same time when timer starts. “H” is output in the count interval of
TZP, and the output is inverted to “L” and stopped when an under-
flow occurs.
Also, when “1” is set to b5 of PUM, the initial level of timer at stop
is “H” and “L” is output at the same time when timer starts. “L” is
output in the count interval of TZP, and the output is inverted to “H”
and stopped when an underflow occurs.
When the INT0 pin one-shot trigger control bit (b6) of PUM is set
to “1”, the one-shot pulse can be output by using the input of INT0
pin as a trigger. The active edge of the pulse input to INT0 pin as
the trigger can be selected by the INT0 pin one-shot trigger active
edge selection bit (b7) of PUM. The trigger is accepted and the
one-shot pulse is generated by the falling edge of INT0 pin input
when “0” is set to b7 of PUM or the rising edge of INT0 pin input
when “1” is set to the b7 of PUM.
Also, the INT0 interrupt occurs when the trigger is input from the
INT0 pin by setting the INT0 interrupt edge selection bit (b0) of the
interrupt edge selection register (INTEDGE) and the INT0 inter-
rupt enable bit (b2) of the interrupt control register 1 (ICON1). Even
when the trigger by the INT0 pin input is selected, the one-shot
pulse can be output by writing to b0 of ONS.
Also, in this mode, the waveform output interval of the one-shot
pulse can be extended for 0.5 cycle of timer count source clock by
setting the timer Z primary waveform extension control bit (b2) to
“1”. As a result, the waveforms of more accurate resolution can be
output.
When using the programmable one-shot generation mode, note
the following;
Notes on using the programmable one-shot generation mode
When setting and changing TZP and EXPZS, write to TZP at last
because the setting to them is executed all at once by writing to
TZP. Even when TZP is not changed, write the same value. The
value is reloaded to timer at the beginning of the next primary in-
terval.
Set by software in order not to execute the writing to timer Z pri-
mary and the timing of timer underflow simultaneously. When read-
ing the timer Z secondary, the undefined value is read out. How-
ever, while timer counts the setting value of the timer Z secondary,
the count values at the secondary interval can be identified by
reading the timer Z primary.
In this mode, set port P0
2
which is also used as TZ
OUT
pin to output.
B2 of PUM can be used only when “00
16
” is set to prescaler Z and
f(X
IN
)/2 or f(X
IN
)/16 is selected as the timer Z count source.
相關PDF資料 |
PDF描述 |
|---|---|
| M37540M4-XXXSP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37560M5-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37560M6-XXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37560M7-XXXGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37560MB-XXXGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37540E2FP | 功能描述:IC 740 MCU OTP 8K 32LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| M37540E2GP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 740 SERIES |
| M37540E2SP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540E8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37540E8FP#U0 | 功能描述:MCU 2/5V 32K PB-FREE 36-SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
發布緊急采購，3分鐘左右您將得到回復。