- 您現在的位置：買賣IC網 > PDF目錄45028 > M34583EDFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | M34583EDFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 122/153頁 |
| 文件大?。?/td> | 947K |
| 代理商： | M34583EDFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁當前第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁
Rev.3.00
Aug 06, 2004
page 70 of 151
REJ03B0009-0300Z
4583 Group
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
Clock control
Execute the main clock (f(XIN)) selection instruction (CMCK,
CRCK or CYCK instruction) in the initial setting routine of pro-
gram (executing it in address 0 in page 0 is recommended).
The oscillation circuit by the CMCK, CRCK or CYCK instruction
can be selected only at once. The oscillation circuit correspond-
ing to the first executed one of these instructions is valid.
The CMCK, CRCK, and CYCK instructions can be used only to
select main clock (f(XIN)). In this time, the start of oscillation and
the switch of system clock are not performed.
When the CMCK, CRCK, and CYCK instructions are never ex-
ecuted, main clock (f(XIN)) cannot be used and system can be
operated only by on-chip oscillator.
The no operated clock source (f(RING)) or (f(XIN)) cannot be
used for the system clock. Also, the clock source (f(RING) or
f(XIN)) selected for the system clock cannot be stopped.
On-chip oscillator
The clock frequency of the on-chip oscillator depends on the sup-
ply voltage and the operation temperature range.
Be careful that variable frequencies when designing application
products.
When considering the oscillation stabilize wait time at the switch
of clock, be careful that the variable frequency of the on-chip os-
cillator clock.
External clock
When the external clock signal for the main clock (f(XIN)) is used,
connect the clock source to XIN pin and XOUT pin open. In pro-
gram, after the CMCK instruction is executed, set main clock
(f(XIN)) oscillation start to be enabled (MR1=0).
For this product, when RAM back-up mode and main clock
(f(XIN)) stop (MR1=1), XIN pin is fixed to “H” in order to avoid the
through current by floating of internal logic. The XIN pin is fixed to
“H” until main clock (f(XIN)) oscillation start to be valid (MR1=0)
by the CMCK instruction from reset state. Accordingly, when an
external clock is used, connect a 1 k
or more resistor to XIN pin
in series to limit of current by competitive signal.
Electric Characteristic Differences Between Mask ROM and One
Time PROM Version MCU
There are differences in electric characteristics, operation mar-
gin, noise immunity, and noise radiation between Mask ROM and
One Time PROM version MCUs due to the difference in the
manufacturing processes.
When manufacturing an application system with the One time
PROM version and then switching to use of the Mask ROM ver-
sion, please perform sufficient evaluations for the commercial
samples of the Mask ROM version.
23
24
25
26
Note on Power Source Voltage
When the power source voltage value of a microcomputer is less
than the value which is indicated as the recommended operating
conditions, the microcomputer does not operate normally and
may perform unstable operation.
In a system where the power source voltage drops slowly when
the power source voltage drops or the power supply is turned off,
reset a microcomputer when the supply voltage is less than the
recommended operating conditions and design a system not to
cause errors to the system by this unstable operation.
27
相關PDF資料 |
PDF描述 |
|---|---|
| M35013-001SP | 24 X 10 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
| M35015-001SP | 24 X 10 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
| M35014-001SP | 24 X 10 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
| M35043-XXXFP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDSO20 |
| M35043-XXXSP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34583MD-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34584EDFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34584MD-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M3459 | 功能描述:電纜固定件和配件 RLTCG 3/8 NPT GRAY NO NUT RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: |
| M3460 | 功能描述:電纜固定件和配件 RLTCG 3/4 NPT BLACK NO NUT RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: |
發布緊急采購，3分鐘左右您將得到回復。