參數資料
型號： M312L5720BZ0-CB3
元件分類： DRAM
英文描述： 256M X 72 DDR DRAM MODULE, 0.7 ns, DMA184
封裝： ROHS COMPLIANT, DIMM-184
文件頁數： 16/30頁
文件大?。?/td> 623K
代理商： M312L5720BZ0-CB3
DDR SDRAM
512MB, 1GB, 2GB Registered DIMM
Rev. 1.0 June 2005
b. Pulldown slew rate is measured under the test conditions shown in Figure 3.
Output
Test point
VDDQ
50
Figure 3 : Pulldown slew rate test load
c. Pullup slew rate is measured between (VDDQ/2 - 320 mV +/- 250 mV)
Pulldown slew rate is measured between (VDDQ/2 + 320 mV +/- 250 mV)
Pullup and Pulldown slew rate conditions are to be met for any pattern of data, including all outputs switching and only one output switching.
Example : For typical slew rate, DQ0 is switching
For minmum slew rate, all DQ bits are switching from either high to low, or low to high.
The remaining DQ bits remain the same as for previous state.
d. Evaluation conditions
Typical
: 25
°C (T Ambient), VDDQ = 2.5V(for DDR266/333) and 2.6V(for DDR400), typical process
Minimum : 70
°C (T Ambient), VDDQ = 2.3V(for DDR266/333) and 2.5V(for DDR400), slow - slow process
Maximum : 0
°C (T Ambient), VDDQ = 2.7V(for DDR266/333) and 2.7V(for DDR400), fast - fast process
e. The ratio of pullup slew rate to pulldown slew rate is specified for the same temperature and voltage, over the entire temperature and voltage range.
For a given output, it represents the maximum difference between pullup and pulldown drivers due to process variation.
f. Verified under typical conditions for qualification purposes.
g. TSOPII package divices only.
h. Only intended for operation up to 266 Mbps per pin.
i. A derating factor will be used to increase tIS and tIH in the case where the input slew rate is below 0.5V/ns as shown in Table 2. The Input slew rate is
based on the lesser of the slew rates detemined by either VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions.
j. A derating factor will be used to increase tDS and tDH in the case where DQ, DM, and DQS slew rates differ, as shown in Tables 3 & 4. Input slew rate
is based on the larger of AC-AC delta rise, fall rate and DC-DC delta rise, Input slew rate is based on the lesser of the slew rates determined by either
VIH(AC) to VIL(AC) or VIH(DC) to VIL(DC), similarly for rising transitions. The delta rise/fall rate is calculated as: {1/(Slew Rate1)} - {1/(Slew Rate2)}
For example : If Slew Rate 1 is 0.5 V/ns and slew Rate 2 is 0.4 V/ns, then the delta rise, fall rate is - 0.5ns/V . Using the table given, this
would result in the need for an increase in tDS and tDH of 100 ps.
k. Table 3 is used to increase tDS and tDH in the case where the I/O slew rate is below 0.5 V/ns. The I/O slew rate is based on the lesser on the lesser of
the AC - AC slew rate and the DC- DC slew rate. The inut slew rate is based on the lesser of the slew rates deter mined by either VIH(ac) to VIL(ac) or
VIH(DC) to VIL(DC), and similarly for rising transitions.
m. DQS, DM, and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transi tions through the
DC region must be monotonic.
a. Pullup slew rate is characteristized under the test conditions as shown in Figure 2.
Output
Test point
VSSQ
50
Figure 2 : Pullup slew rate test load
15.0 System Notes:
相關PDF資料
PDF描述
M312L5720DZ3-CB3 256M X 72 DDR DRAM MODULE, 0.7 ns, DMA184
M32002AMMJFREQ VCXO, CLOCK, 150 MHz - 1400 MHz, CMOS OUTPUT
M32016BGPJFREQ VCXO, CLOCK, 150 MHz - 1400 MHz, PECL OUTPUT
M32026AUMJFREQ VCXO, CLOCK, 150 MHz - 1400 MHz, CMOS OUTPUT
M32012BGPJFREQ VCXO, CLOCK, 150 MHz - 1400 MHz, PECL OUTPUT
相關代理商/技術參數
參數描述
M312L5720CZ3-CCC00 制造商:Samsung Semiconductor 功能描述:512 DDR SDRAM MODUL X72 BOC(LF) - Trays
M312L6420ETS 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:DDR SDRAM Registered Module
M312L6420HUS 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:DDR SDRAM Product Guide
M312L6420HUS-CB000 制造商:Samsung Semiconductor 功能描述:256 DDR SDRAM MODUL X72 TSOP2-400(LF) - Trays
M312L6420JUS 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:DDR SDRAM Product Guide
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*