- 您現在的位置：買賣IC網 > PDF目錄180109 > M24C01-RMB3T/S (STMICROELECTRONICS) 128 X 8 I2C/2-WIRE SERIAL EEPROM, DSO8 PDF資料下載
參數資料
| 型號： | M24C01-RMB3T/S |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 128 X 8 I2C/2-WIRE SERIAL EEPROM, DSO8 |
| 封裝： | 2 X 3 MM, MLP-8 |
| 文件頁數： | 3/33頁 |
| 文件大小： | 278K |
| 代理商： | M24C01-RMB3T/S |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
M24C16, M24C08, M24C04, M24C02, M24C01
Device operation
3
Device operation
The device supports the IC protocol. This is summarized in Figure 5. Any device that sends
data on to the bus is defined to be a transmitter, and any device that reads the data to be a
receiver. The device that controls the data transfer is known as the bus master, and the
other as the slave device. A data transfer can only be initiated by the bus master, which will
also provide the serial clock for synchronization. The M24Cxx device is always a slave in all
communication.
3.1
Start condition
Start is identified by a falling edge of Serial Data (SDA) while Serial Clock (SCL) is stable in
the High state. A Start condition must precede any data transfer command. The device
continuously monitors (except during a Write cycle) Serial Data (SDA) and Serial Clock
(SCL) for a Start condition, and will not respond unless one is given.
3.2
Stop condition
Stop is identified by a rising edge of Serial Data (SDA) while Serial Clock (SCL) is stable
and driven High. A Stop condition terminates communication between the device and the
bus master. A Read command that is followed by NoAck can be followed by a Stop condition
to force the device into the Stand-by mode. A Stop condition at the end of a Write command
triggers the internal Write cycle.
3.3
Acknowledge Bit (ACK)
The acknowledge bit is used to indicate a successful byte transfer. The bus transmitter,
whether it be bus master or slave device, releases Serial Data (SDA) after sending eight bits
of data. During the 9th clock pulse period, the receiver pulls Serial Data (SDA) Low to
acknowledge the receipt of the eight data bits.
3.4
Data input
During data input, the device samples Serial Data (SDA) on the rising edge of Serial Clock
(SCL). For correct device operation, Serial Data (SDA) must be stable during the rising edge
of Serial Clock (SCL), and the Serial Data (SDA) signal must change only when Serial Clock
(SCL) is driven Low.
相關PDF資料 |
PDF描述 |
|---|---|
| M253216FCNFREQ | CRYSTAL OSCILLATOR, CLOCK, 1 MHz - 66 MHz, HCMOS OUTPUT |
| M255FAN1.5000MHZ | CRYSTAL OSCILLATOR, CLOCK, 1.5 MHz, HCMOS/TTL OUTPUT |
| M273QCN1.5000MHZ | CRYSTAL OSCILLATOR, CLOCK, 1.5 MHz, HCMOS OUTPUT |
| M275QANFREQ1 | CRYSTAL OSCILLATOR, CLOCK, 1.5 MHz - 135 MHz, HCMOS/TTL OUTPUT |
| M234FAN1.5000MHZ | CRYSTAL OSCILLATOR, CLOCK, 1.5 MHz, HCMOS/TTL OUTPUT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M24C01RMB5TG | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Kbit, 8 Kbit, 4 Kbit, 2 Kbit and 1 Kbit serial IC bus EEPROM |
| M24C01RMB5TP | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16 Kbit, 8 Kbit, 4 Kbit, 2 Kbit and 1 Kbit serial IC bus EEPROM |
| M24C01-RMB6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit Serial I2C Bus EEPROM |
| M24C01-RMB6/S | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit Serial I2C Bus EEPROM |
| M24C01-RMB6/W | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16Kbit, 8Kbit, 4Kbit, 2Kbit and 1Kbit Serial I2C Bus EEPROM |
發布緊急采購，3分鐘左右您將得到回復。