- 您現在的位置：買賣IC網 > PDF目錄98003 > LTC4090EDJC#TRPBR (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO22 PDF資料下載
參數資料
| 型號： | LTC4090EDJC#TRPBR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO22 |
| 封裝： | 6 X 3 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, MO-229WXXX, DFN-22 |
| 文件頁數： | 2/28頁 |
| 文件大?。?/td> | 392K |
| 代理商： | LTC4090EDJC#TRPBR |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC4090
10
4090f
CLPROG (Pin 14): Current Limit Program and Input Cur-
rent Monitor. Connecting a resistor, RCLPROG, to ground
programs the input to output current limit. The current
limit is programmed as follows:
IA
V
R
CL
CLPROG
()
=
1000
In USB applications, the resistor RCLPROG should be set
to no less than 2.1k. The voltage on the CLPROG pin is
always proportional to the current owing through the
IN to OUT power path. This current can be calculated as
follows:
IA
V
R
IN
CLPROG
()
=
1000
HPWR (Pin 15): High Power Select. This logic input is used
to control the input current limit. A voltage greater than
1.2V on the pin will set the input current limit to 100% of
the current programmed by the CLPROG pin. A voltage
less than 0.4V on the pin will set the input current limit to
20% of the current programmed by the CLPROG pin. A
2μA pull-down current is internally connected to this pin
to ensure it is low at power up when the pin is not being
driven externally.
SUSP (Pin 16): Suspend Mode Input. Pulling this pin
above 1.2V will disable the power path from IN to OUT.
The supply current from IN will be reduced to comply
with the USB specication for suspend mode. Both the
ability to charge the battery from HVIN and the ideal diode
function (from BAT to OUT) will remain active. Suspend
mode will reset the charge timer if OUT is less than BAT
while in suspend mode. If OUT is kept greater than BAT,
such as when the high voltage input is present, the charge
timer will not be reset when the part is put in suspend. A
2μA pull-down current is internally connected to this pin
to ensure it is low at power up when the pin is not being
driven externally.
TIMER (Pin 17): Timer Capacitor. Placing a capacitor,
CTIMER, to GND sets the timer period. The timer period
is:
t
hours
C
R
hours
F
k
TIMER
PROG
()
.
=
3
0 1
100
Charge time is increased if charge current is reduced
due to load current, thermal regulation and current limit
selection (HPWR low).
Shorting the TIMER pin to GND disables the battery
charging functions.
HVOUT (Pin 18): Voltage Output of the High Voltage
Regulator. When sufcient voltage is present at HVOUT,
the low voltage power path from IN to OUT will be discon-
nected and the HVPR pin will be pulled low to indicate
that a high voltage wall adapter has been detected. The
LTC4090 high voltage regulator will maintain just enough
differential voltage between HVOUT and BAT to keep the
battery charger MOSFET out of dropout (typically 300mV
from OUT to BAT). HVOUT should be bypassed with at
least 22μF to GND.
BOOST (Pin 19): This pin is used to provide drive voltage,
higher than the input voltage, to the internal bipolar NPN
power switch.
SW (Pin 20): The SW pin is the output of the internal high
voltage power switch. Connect this pin to the inductor,
catch diode and boost capacitor.
HVIN (Pin 21): High Voltage Regulator Input. The HVIN pin
supplies current to the internal high voltage regulation and
to the internal high voltage power switch. The presence
of a high voltage input takes priority over the USB VBUS
input (i.e., when a high voltage input supply is detected,
the USB IN to OUT path is disconnected). This pin must
be locally bypassed.
HVEN (Pin 22): High Voltage Regulator Enable Input. The
HVEN pin is used to disable the high voltage input path.
Tie to ground to disable the high voltage input or tie to at
least 2.3V to enable the high voltage path. If this feature
is not used, tie HVEN to the HVIN pin. This pin can also
be used to soft-start the high voltage regulator; see the
Applications Information section for more information.
Exposed Pad (Pin 23): Ground. The exposed package
pad is ground and must be soldered to the PC board for
proper functionality and for maximum heat transfer (use
several vias directly under the LTC4090).
PIN FUNCTIONS
相關PDF資料 |
PDF描述 |
|---|---|
| LTC6103CMS8#TR | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC6103HMS8#TR | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC6604CUFF-10#TRPBF | SPECIALTY ANALOG CIRCUIT, PQCC34 |
| LUC025F | 2-OUTPUT 16.5 W DC-DC REG PWR SUPPLY MODULE |
| LV56801P | 1-CHANNEL POWER SUPPLY SUPPORT CKT, ZIP15 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4095 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Standalone USB Li-Ion/Polymer Battery Charger in 2mm × 2mm DFN |
| LTC4095EDC | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Standalone USB Li-Ion/Polymer Battery Charger in 2mm × 2mm DFN |
| LTC4095EDC#TRMPBF | 功能描述:IC CHARGER LI-ION/POLY 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC4095EDC#TRPBF | 功能描述:IC CHARGER LI-ION/POLY 8-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC4096 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Input Standalone Li-Ion Battery Chargers |
發布緊急采購，3分鐘左右您將得到回復。