- 您現在的位置：買賣IC網 > PDF目錄44990 > LTC3226EUD#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHED CAPACITOR REGULATOR, PQCC16 PDF資料下載
參數資料
| 型號： | LTC3226EUD#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHED CAPACITOR REGULATOR, PQCC16 |
| 封裝： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-220WEED-2, QFN-16 |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 431K |
| 代理商： | LTC3226EUD#TRPBF |
LTC3226
11
3226f
APPLICATIONS INFORMATION
Programming the Supercapacitor
Termination Voltage (CPO)
The termination voltage of the supercapacitor stack on
the CPO pin can be programmed for any voltage between
2.5V to 5.3V by using a resistor divider from the CPO pin
to GND via the CPO_FB pin such that:
VCPO = VCPO_FB 1+
RCP1
RCP2
where VCPO_FB is 1.2V. See the block diagram in Figure1.
Typical values for RCP1 and RCP2 are in the range of 40k
to 5M.
Programming the Input Current Limit for the Charger
The input current limit for the LTC3226 charge pump is
programmed by using a single resistor from the PROG
pin to ground. The input current limit is typically 10,500
times the current out of the PROG pin. The PROG pin
voltage always servos to 1V as long as the part is not in
sleep mode. The program resistor and the input current
limit are calculated using the following equations:
RPROG =10,500
1V
IVIN(ILIM)
, IVIN(ILIM) =10,500
1V
RPROG
where IVIN(ILIM) is the input current limit for the charge
pump charger. The maximum allowable input current limit
of 315mA can be achieved by using a PROG resistor of
33.2k. To maximize the charge transfer rate, the charge
pumpoperatesin1xmodewhenthesupercapacitorvoltage
is less than the input voltage and the charge current out of
CPO pin is only limited by the programmed input current
limit. However, in 2x mode, the average charge current is
approximately half the input current limit.
Programming the Input Voltage Threshold for the
Power-Fail Comparator
The input voltage threshold below which the power-fail
status pin PFO indicates a power-fail condition and the
LTC3226switchestheinternalLDOoncanbeprogrammed
by using a resistor divider from the VIN pin to GND via the
PFI pin such that:
VIN(PFO_HI_LO) = VPFI 1+
RPF1
RPF2
where VPFI is 1.2V. See Figure 1. Typical values for RPF1
and RPF2 are in the range of 40k to 5M. For a smooth
transition from normal to back-up mode, the PFI threshold
should be set 50mV to 100mV above the programmed
LDO output voltage, VOUT.
The input voltage above which the power-fail status pin
PFO is high impedance and the supercapacitor charger
and the ideal diode are enabled is:
VIN(PFO_LO_HI) = VPFI + VPFI(HYS)
(
) 1+RPF1
RPF2
where VPFI(HYS) is the hysteresis of the PFI comparator. It
is internally set to a typical value of 20mV.
The hysteresis can be increased externally by adding a
resistor,RH,inserieswithadiode,D1,betweenthePFOand
PFI pins as shown in Figure 2. This network will increase
the low-to-high VIN threshold for PFO while keeping the
high-to-low threshold intact. The increase in hysteresis
at the input can be calculated as shown:
VIN(HYS) = VPFI + VPFI(HYS) – VF
(
)RPF1
RH
相關PDF資料 |
PDF描述 |
|---|---|
| LTC3226IUD#PBF | SWITCHED CAPACITOR REGULATOR, PQCC16 |
| LTC3400BES6#PBF | 0.85 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3404MPMS8#PBF | 1.5 A SWITCHING REGULATOR, 1650 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3404IMS8#PBF | 1.5 A SWITCHING REGULATOR, 1650 kHz SWITCHING FREQ-MAX, PDSO8 |
| LTC3404MPMS8#TRPBF | 1.5 A SWITCHING REGULATOR, 1650 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC3226IUD | 制造商:LINEAR 制造商全稱:LINEAR 功能描述:2-Cell Supercapacitor Charger with Backup PowerPath Controller |
| LTC3226IUD#PBF | 功能描述:IC 2CELL SUPERCAP CHARGE 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3226IUD#TRPBF | 功能描述:IC 2CELL SUPERCAP CHARGE 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:PowerPath™ 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LTC3230 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:5-LED Main/Sub Display Driver with Dual LDO |
| LTC3230EUD#PBF | 功能描述:IC LED DRIVR WHITE BCKLGT 20-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 恒定電流:- 恒定電壓:- 拓撲:升壓（升壓），切換式電容器（充電泵） 輸出數:1 內部驅動器:是 類型 - 主要:背光 類型 - 次要:白色 LED 頻率:625kHz ~ 875kHz 電源電壓:2.7 V ~ 5.3 V 輸出電壓:5V 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-µMAX 包裝:帶卷 (TR) 工作溫度:-40°C ~ 85°C |
發布緊急采購，3分鐘左右您將得到回復。