- 您現在的位置：買賣IC網 > PDF目錄385506 > LTC2428C (Linear Technology Corporation) 16-Bit 2.5-V to 3.3-V/3.3-V To 5-V Level Shifting Transceiver With 3-State Outputs 56-BGA MICROSTAR JUNIOR -40 to 85 PDF資料下載
參數資料
| 型號： | LTC2428C |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 16-Bit 2.5-V to 3.3-V/3.3-V To 5-V Level Shifting Transceiver With 3-State Outputs 56-BGA MICROSTAR JUNIOR -40 to 85 |
| 中文描述： | 4-/8-Channel 20位ADC的無延遲uPower |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 317K |
| 代理商： | LTC2428C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
17
LTC2424/LTC2428
APPLICATIO
S I
N
FOR
ATIO
U
W
U
The device remains in the sleep state until the first rising
edge of SCK is seen while CSADC is LOW. Data is
shifted
out the SDO pin on each falling edge of SCK. This enables
external circuitry to latch the output on the rising edge of
SCK. EOC can be latched on the first rising edge of SCK
and the last bit of the conversion result can be latched on
the 24th rising edge of SCK. On the 24th falling edge of
SCK, the device begins a new conversion. SDO goes HIGH
(EOC = 1) indicating a conversion is in progress.
At the conclusion of the data cycle, CSADC may remain
LOW and EOC monitored as an end-of-conversion inter-
rupt. Alternatively, CSADC may be driven HIGH setting
SDO to HI-Z. As described above, CSADC may be pulled
LOW at any time in order to monitor the conversion status.
For each of these operations, CSMUX may be tied to
CSADC without affecting the selected channel.
At the conclusion of the data output cycle, the converter
enters a user transparent calibration cycle prior to actually
performing a conversion on the selected input channel.
This enables a 66ms (for 60Hz notch frequency) look ahead
time for the multiplexer input. Following the data output
cycle, the multiplexer input channel may be selected any
time in this 66ms window by pulling CSADC HIGH and
serial shifting data into the D
IN
pin, see Figure 14.
While the device is performing the internal calibration, it is
sensitive to ground current disturbances. Error currents
flowing in the ground pin may lead to offset errors. If the
SCK pin is toggling during the calibration, these ground
disturbances will occur. The solution is to either drive the
multiplexer clock input (CLK) separately from the ADC
clock input (SCK), or program the multiplexer in the first
1ms following the data output cycle. The remaining 65ms
may be used to allow the input signal to settle.
Typically, CSADC remains LOW during the data output
state. However, the data output state may be aborted by
pulling CSADC HIGH anytime between the first rising edge
and the 24th falling edge of SCK, see Figure 15. On the
rising edge of CSADC, the device aborts the data output
state and immediately initiates a new conversion. This is
useful for systems not requiring all 24 bits of output data,
aborting an invalid conversion cycle or synchronizing the
start of a conversion.
Internal Serial Clock
This timing mode uses an internal serial clock to shift out
the conversion result and program the multiplexer, see
Figure 16. A CS signal directly drives the CSADC input,
while the inverse of CS drives the CSMUX input. The CS
SCK/CLK
SDO
D
IN
CSADC/
CSMUX
V
CC
F
O
FS
SET
CSMUX
CSADC
SCK
CLK
MUXOUT
ADCIN
D
IN
SDO
ZS
SET
GND
0.1V
TO V
CC
–0.12V
REF
TO 1.12V
REF
CH0
TO CH7
2.7V TO 5.5V
LTC2424/LTC2428
MSB
EXR
SIG
BIT0
LSB
BIT4
BIT19 BIT18
BIT20
BIT21
BIT22
BIT23
24248 F13
= 50Hz REJECTION
= EXTERNAL OSCILLATOR
= 60Hz REJECTION
V
CC
TEST EOC
DON’T CARE
DON’T CARE
EN
D2
D1
D0
Hi-Z
Hi-Z
TEST EOC
Hi-Z
TEST EOC
CS
SCK
Figure 13. External Serial Clock Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2428CG | 4-/8-Channel 20-Bit uPower No Latency ADCs |
| LTC2428I | 4-/8-Channel 20-Bit uPower No Latency ADCs |
| LTC2428IG | 4-/8-Channel 20-Bit uPower No Latency ADCs |
| LTC2442 | 24-Bit High Speed 4-Channel Delta-Sigma ADC with Integrated Amplifi er |
| LTC2442CG | 24-Bit High Speed 4-Channel Delta-Sigma ADC with Integrated Amplifi er |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2428CG | 功能描述:IC ADC 20BIT 8CH MICROPWR 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2428CG#PBF | 功能描述:IC ADC 20BIT 8CH MICROPWR 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2428CG#TR | 功能描述:IC ADC 20BIT 8CH MICROPWR 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2428CG#TRPBF | 功能描述:IC ADC 20BIT 8CH MICROPWR 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2428CGPBF | 制造商:Linear Technology 功能描述:ADC,LTC2428C 20bit D-S 8 ch SPI SSOP |
發布緊急采購，3分鐘左右您將得到回復。