- 您現在的位置：買賣IC網 > PDF目錄384633 > LTC1760 (Linear Technology Corporation) Dual Smart Battery System Manager PDF資料下載
參數資料
| 型號： | LTC1760 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Dual Smart Battery System Manager |
| 中文描述： | 雙智能電池系統管理 |
| 文件頁數： | 24/44頁 |
| 文件大?。?/td> | 379K |
| 代理商： | LTC1760 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
LTC1760
24
sn1760 1760is
2.6 LTC1760 SMBALERT Operation
The SMBALERT pin allows the LTC1760 to signal to the
SMBus Host that there has been a change of status.
This pin is asserted low whenever there is a change in
battery presence, AC presence or after a power on reset
event. This pin is cleared during an Alert Response or
any of the following reads:
BatterySystemState(),BatterySystemStateCont(),
BatterySystemInfo(), or LTC().
3 Charging Algorithm Overview
3.1 Wake-Up Charging Initiation
The following conditions must be met in order to allow
wake-up charging:
1. The battery thermistor must be COLD-RANGE, IDEAL-
RANGE, or UNDER-RANGE.
2. AC must be present.
3. BatterySystemStateCont(CHARGING_INHIBIT) must be
de-asserted (or low).
4. Hardware controlled charging inhibit must be
de-asserted (MODE not low with V
DDS
high)
Wake-up charging initiates when a newly inserted battery
does not respond to any LTC1760 master read com-
mands. Only one battery will wake-up charge at a time.
When two batteries are inserted and both require wake-up
charging, Battery 1 will wake-up charge first. Battery 2 will
only wake-up charge when Battery 1 terminates wake-up
charging.
Wake-up charging takes priority over controlled charging;
this prevents one battery from tying up the charger when
it would be advantageous to dual charge two deeply
discharged batteries.
The LTC1760 will attempt to reinitiate wake-up
charging on both batteries after the SMBus Host asserts
BatterySystemStateCont(CHARGER_POR) or a power on
reset event. This will reset any wake-up charging safety
timers and is equivalent to removing and reinserting both
batteries.
The LTC1760 will attempt to reinitiate wake-up charging
on a battery if the battery is not being charged and fails to
respond to an SMBus query. This is an important feature
for handling deeply discharged NiMh batteries. These
batteries may begin to talk while being charged and go
silent once charging has stopped.
Wake-up charging is disabled if the battery thermistor is
COLD-RANGE or UNDER-RANGE and the battery has been
charged for longer than t
TIMEOUT
.
3.2 Wake-Up Charging Termination
The LTC1760 will terminate wake-up charging when any of
the following conditions are met:
1. Battery removal (thermistor indicating OVER-RANGE)
2. AC is removed.
3. The SMBus Host issues a calibration request by setting
BatterySystemStateCont(CALIBRATE) high.
4. Any response to an LTC1760 master read of
ChargingCurrent(), Current(), ChargingVoltage(), or Volt-
age(). Note that the LTC1760 ignores all writes from the
battery.
5. Any of the following AlarmWarning() bits asserted high:
OVER_CHARGED_ALARM
TERMINATE_CHARGE_ALARM
TERMINATE_CHARGE_RESERVED
OVER_TEMP_ALARM
Note that the LTC1760 ignores all writes from the battery.
Each battery’s charge alarm is cached inside the LTC1760.
This bit will be set when any of the upper four bits of the
battery’s AlarmWarning() response are set. This bit will
remain set if a subsequent AlarmWarning() fails to re-
spond. The cached alarm will be cleared by any of the
following conditions.
a) Associated battery is removed.
b) A subsequent AlarmWarning() clears all
charge alarm bits for the associated battery.
c) A power on reset event.
d) The SMBus Host asserts
BatterySystemStateCont(CHARGER_POR) high.
6. An SMBus Host write asserts the LTC1760
BatterySystemStateCont(CHARGING_INHIBIT) high.
OPERATIOU
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1760CFW | Dual Smart Battery System Manager |
| LTC2286 | Dual 10-Bit, 65/40/25Msps Low Noise 3V ADCs |
| LTC2286CUP | Dual 10-Bit, 65/40/25Msps Low Noise 3V ADCs |
| LTC2286IUP | Dual 10-Bit, 65/40/25Msps Low Noise 3V ADCs |
| LTC2286UP | Dual 10-Bit, 65/40/25Msps Low Noise 3V ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1760CFW | 功能描述:IC MANAGER BATTERY DUAL 48TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1760CFW#PBF | 功能描述:IC MANAGER BATTERY DUAL 48TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC1760CFW#PBF | 制造商:Linear Technology 功能描述:Battery Management IC 制造商:Linear Technology 功能描述:IC, BATTERY CHARGER, 4.28A, TSSOP-48 |
| LTC1760CFW#TR | 功能描述:IC MANAGER BATTERY SYS 48-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1760CFW#TRPBF | 功能描述:IC MANAGER BATTERY DUAL 48TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。