- 您現在的位置：買賣IC網 > PDF目錄385501 > LT1622 (Linear Technology Corporation) Low Input Voltage Current Mode Step-Down DC/DC Controller(低輸入電壓，電流模式步降DC/DC控制器) PDF資料下載
參數資料
| 型號： | LT1622 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Low Input Voltage Current Mode Step-Down DC/DC Controller(低輸入電壓，電流模式步降DC/DC控制器) |
| 中文描述： | 低輸入電壓電流模式降壓DC / DC控制器（低輸入電壓，電流模式步降直流/直流控制器） |
| 文件頁數： | 7/16頁 |
| 文件大?。?/td> | 223K |
| 代理商： | LT1622 |
7
LTC1622
APPLICATIO
S I
N
FOR
ATIO
U
The basic LTC1622 application circuit is shown in Figure
1. External component selection is driven by the load
requirement and begins with the selection of L and R
SENSE
.
Next, the Power MOSFET and the output diode D1 are
selected followed by C
IN
and C
OUT
.
W
U
Kool Mu is a registered trademark of Magnetics, Inc.
R
SENSE
Selection for Output Current
R
SENSE
is chosen based on the required output current.
With the current comparator monitoring the voltage devel-
oped across R
SENSE
, the threshold of the comparator
determines the inductor’s peak current. The output cur-
rent the LTC1622 can provide is given by:
I
R
I
OUT
SENSE
RIPPLE
2
=
0 08
where I
RIPPLE
is the inductor peak-to-peak ripple current
(see Inductor Value Calculation section).
A reasonable starting point for setting ripple current is
I
RIPPLE
= (0.4)(I
OUT
). Rearranging the above equation, it
becomes:
R
I
SENSE
OUT
=
( )(
)
1
15
for Duty Cycle < 40%
However, for operation that is above 40% duty cycle, slope
compensation has to be taken into consideration to select
the appropriate value to provide the required amount of
current. Using Figure 2, the value of R
SENSE
is:
R
SF
I
SENSE
OUT
=
( )(
)(
)
15
100
Inductor Value Calculation
The operating frequency and inductor selection are inter-
related in that higher operating frequencies permit the use
of a smaller inductor for the same amount of inductor
ripple current. However, this is at the expense of efficiency
due to an increase in MOSFET gate charge losses.
The inductance value also has a direct effect on ripple
current. The ripple current, I
RIPPLE
, decreases with higher
inductance or frequency and increases with higher V
IN
or
V
OUT
. The inductor’s peak-to-peak ripple current is given
by:
I
V
V
f L
( )
V
V
V
V
RIPPLE
IN
OUT
OUT
D
IN
D
=
+
+
where f is the operating frequency. Accepting larger values
of I
RIPPLE
allows the use of low inductances, but results in
higher output voltage ripple and greater core losses. A
reasonable starting point for setting ripple current is
I
RIPPLE
= 0.4(I
OUT(MAX)
). Remember, the maximum I
RIPPLE
occurs at the maximum input voltage.
With Burst Mode operation selected on the LTC1622, the
ripple current is normally set such that the inductor
current is continuous during the burst periods. Therefore,
the peak-to-peak ripple current should not exceed:
I
R
RIPPLE
SENSE
≤
0 036
This implies a minimum inductance of:
L
V
V
f
R
V
V
V
V
MIN
IN
OUT
SENSE
OUT
D
IN
D
=
+
+
0 036
(Use V
IN(MAX)
= V
IN
)
A smaller value than L
MIN
could be used in the circuit;
however, the inductor current will not be continuous
during burst periods.
Inductor Core Selection
Once the value for L is known, the type of inductor must be
selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite, molypermalloy
or Kool Mu
cores. Actual core loss is independent of core
size for a fixed inductor value, but it is very dependent on
inductance selected. As inductance increases, core losses
go down. Unfortunately, increased inductance requires
more turns of wire and therefore copper losses will
increase. Ferrite designs have very low core losses and are
相關PDF資料 |
PDF描述 |
|---|---|
| LT1632 | 45MHz, 45V/us, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps |
| LT1632CN8 | 45MHz, 45V/us, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps |
| LT1632CS8 | 45MHz, 45V/us, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps |
| LT1633 | 45MHz, 45V/us, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps |
| LT1633CS | 45MHz, 45V/us, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1624IS8 | 制造商:Linear Technology 功能描述: |
| LT-1625S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:T1/CEPT/ISDN-PRI TRANSFORMER |
| LT1627 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Low Dropout Regulators with Shutdown |
| LT1629 | 制造商:EDSYN 功能描述: |
| LT1630 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:30MHz, 10V/us, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps |
發布緊急采購，3分鐘左右您將得到回復。