參數資料
型號: LPC2939FBD208
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: ARM9 microcontroller with CAN, LIN, and USB
中文描述: 32-BIT, FLASH, 125 MHz, RISC MICROCONTROLLER, PQFP208
封裝: 28 X 28 MM, 1.40 MM HEIGHT, PLASTIC, SOT-459, MS-026, LQFP-208
文件頁數: 17/99頁
文件大?。?/td> 1945K
代理商: LPC2939FBD208
LPC2939_3
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 03 — 7 April 2010
17 of 99
NXP Semiconductors
LPC2939
ARM9 microcontroller with CAN, LIN, and USB
6.6 Reset, debug, test, and power description
6.6.1
Reset and power-up behavior
The LPC2939 contains external reset input and internal power-up reset circuits. This
ensures that a reset is extended internally until the oscillators and flash have reached a
stable state. See
Section 8
for trip levels of the internal power-up reset circuit
1
. See
Section 9
for characteristics of the several start-up and initialization times.
Table 4
shows
the reset pin.
Table 4.
Symbol
RST
At activation of the RST pin the JTAGSEL pin is sensed as logic LOW. If this is the case
the LPC2939 is assumed to be connected to debug hardware, and internal circuits
re-program the source for the BASE_SYS_CLK to be the crystal oscillator instead of the
Low-Power Ring Oscillator (LP_OSC). This is required because the clock rate when
running at LP_OSC speed is too low for the external debugging environment.
6.6.2
Reset strategy
The LPC2939 contains a central module, the Reset Generator Unit (RGU) in the Power,
Clock and Reset Subsystem (PCRSS), which controls all internal reset signals towards
the peripheral modules. The RGU provides individual reset control as well as the
monitoring functions needed for tracing a reset back to source.
6.6.3
IEEE 1149.1 interface pins (JTAG boundary-scan test)
The LPC2939 contains boundary-scan test logic according to IEEE 1149.1, also referred
to in this document as Joint Test Action Group (JTAG). The boundary-scan test pins can
be used to connect a debugger probe for the embedded ARM processor. Pin JTAGSEL
selects between boundary-scan mode and debug mode.
Table 5
shows the boundary-
scan test pins.
Table 5.
Symbol
JTAGSEL
1.
Only for 1.8 V power sources
Reset pin
Direction
IN
Description
external reset input, active LOW; pulled up internally
IEEE 1149.1 boundary-scan test and debug interface
Description
TAP controller select input. LOW level selects ARM debug mode and HIGH level
selects boundary scan and flash programming; pulled up internally
test reset input; pulled up internally (active LOW)
test mode select input; pulled up internally
test data input, pulled up internally
test data output
test clock input
TRST
TMS
TDI
TDO
TCK
相關PDF資料
PDF描述
LPC3180FEL320 16-32-bit ARM microcontroller; hardware floating-point coprocessor, USB On-The-Go, and SDRAM memory interface
LPC3220FET296 ARM926EJ-S with 128 kB SRAM, USB High-speed OTG, SD-MMC, NAND flash controller
LPC3230FET296 ARM926EJ-S with 256 kB SRAM, USB High-speed OTG, SD-MMC, NAND flash controller, LCD controller
LPC3240FET296 ARM926EJ-S with 256 kB SRAM, USB High-speed OTG, SD-MMC, NAND flash controller, Ethernet
LPV531 Programmable Micropower CMOS Input, Rail-to-Rail Output Operational Amplifier
相關代理商/技術參數
參數描述
LPC2939FBD208,551 功能描述:ARM微控制器 - MCU IC ARM9 MCU FLASH 768KB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2939FBD208551 制造商:NXP Semiconductors 功能描述:MCU ARM9 208LQFP
LPC2939FET208,551 功能描述:ARM微控制器 - MCU LPC2939FET208/TFBGA208/TRAYBDP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC-2FS01 制造商:Honda Tsushin Kogyo Co Ltd 功能描述:CABLE CRIMPING TYPE FEMALE INSULATOR
LPC3130 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-cost, low-power ARM926EJ-S MCUs with high-speed USB 2.0 OTG, SD/MMC, and NAND flash controller