參數資料
型號: LPC2478FET208
廠商: NXP Semiconductors N.V.
元件分類: 數學處理器
英文描述: Single-chip 16-bit-32-bit micro; 512 kB flash, Ethernet, CAN, LCD, USB 2.0 device-host-OTG, external memory interface
封裝: LPC2478FBD208<SOT459-1 (LQFP208)|<<http://www.nxp.com/packages/SOT459-1.html<1<Always Pb-free,;LPC2478FET208<SOT950-1 (TFBGA208)|<<http://www.nxp.com/packages/SOT950-1.ht
文件頁數: 34/93頁
文件大?。?/td> 751K
代理商: LPC2478FET208
LPC2478
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 3 — 12 September 2011
34 of 93
NXP Semiconductors
LPC2478
Single-chip 16-bit/32-bit microcontroller
One AHB master for transferring data. This interface transfers data when a DMA
request goes active.
32-bit AHB master bus width.
Incrementing or non-incrementing addressing for source and destination.
Programmable DMA burst size. The DMA burst size can be programmed to more
efficiently transfer data. Usually the burst size is set to half the size of the FIFO in the
peripheral.
Internal four-word FIFO per channel.
Supports 8-bit, 16-bit, and 32-bit wide transactions.
An interrupt to the processor can be generated on a DMA completion or when a DMA
error has occurred.
Interrupt masking. The DMA error and DMA terminal count interrupt requests can be
masked.
Raw interrupt status. The DMA error and DMA count raw interrupt status can be read
prior to masking.
7.9 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back as well as the current state of the port pins.
LPC2478 use accelerated GPIO functions:
GPIO registers are relocated to the ARM local bus so that the fastest possible I/O
timing can be achieved.
Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
All GPIO registers are byte and half-word addressable.
Entire port value can be written in one instruction.
Additionally, any pin on port 0 and port 2 (total of 64 pins) that is not configured as an
analog input/output can be programmed to generate an interrupt on a rising edge, a falling
edge, or both. The edge detection is asynchronous, so it may operate when clocks are not
present such as during Power-down mode. Each enabled interrupt can be used to wake
the chip up from Power-down mode.
7.9.1
Features
Bit level set and clear registers allow a single instruction to set or clear any number of
bits in one port.
Direction control of individual bits.
All I/O default to inputs after reset.
Backward compatibility with other earlier devices is maintained with legacy port 0 and
port 1 registers appearing at the original addresses on the APB.
相關PDF資料
PDF描述
LPC2917FBD144 ARM9 microcontroller with CAN and LIN
LPC2919FBD144 ARM9 microcontroller with CAN and LIN
LPC2921FBD100 ARM9 microcontroller with CAN, LIN, and USB
LPC2923FBD100 ARM9 microcontroller with CAN, LIN, and USB
LPC2925FBD100 ARM9 microcontroller with CAN, LIN, and USB
相關代理商/技術參數
參數描述
LPC2478FET208,551 功能描述:ARM微控制器 - MCU LCD CONT/ETHNET USB/512K FL RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2478FET208551 制造商:NXP Semiconductors 功能描述:MCU ARM7 208TFBGA
LPC2478-STK 功能描述:開發板和工具包 - ARM DEV BRD FOR LPC2478 64MB SDRAM 100MBIT RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
LPC2478-STK-MICTOR 功能描述:開發板和工具包 - ARM DEV BRD FOR LPC2478 RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
LPC-24B-12R 制造商:OPTIFUSE 功能描述: