- 您現在的位置：買賣IC網 > PDF目錄384605 > LMX9838SBX (NATIONAL SEMICONDUCTOR CORP) Bluetooth Serial Port Module PDF資料下載
參數資料
| 型號： | LMX9838SBX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Bluetooth Serial Port Module |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA70 |
| 封裝： | 10 X 17 MM, 2 MM HEIGHT, LGA-70 |
| 文件頁數： | 15/26頁 |
| 文件大小： | 974K |
| 代理商： | LMX9838SBX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
30027906
FIGURE 6. UART NULL Modem Connection
14.2.2 Disabling the UART transport layer
The Host can disable the UART transport layer by sending
the “Disable Transport Layer” Command. The LMX9838 will
empty its buffers, send the confirmation event and disable its
UART interface. Afterwards the UART interface will be re-
configured to wake up on a falling edge of the CTS pin.
14.2.3 LMX9838 enabling the UART interface
As the Transport Layer can be disabled in any situation the
LMX9838 must first make sure the transport layer is enabled
before sending data to the host. Possible scenarios can be
incoming data or incoming link indicators. If the UART is not
enabled the LMX9838 assumes that the Host is sleeping and
waking it up by activating RTS. To be able to react on that
Wake up, the host has to monitor the CTS pin.
As soon as the host activates its RTS pin, the LMX9838 will
first send a confirmation event and then start to transmit the
events.
14.2.4 Enabling the UART transport layer from the host
If the host needs to send data or commands to the LMX9838
while the UART Transport Layer is disabled it must first as-
sume that the LMX9838 is sleeping and wake it up using its
RTS signal. When the LMX9838 detects the Wake-Up signal
it activates the UART HW and acknowledges the Wake-Up
signal by settings its RTS. Additionally the Wake up will be
confirmed by a confirmation event. When the Host has re-
ceived this “Transport Layer Enabled” event, the LMX9838 is
ready to receive commands.
15.0 Command Interface
The LMX9838 offers Bluetooth functionality in either a self
contained slave functionality or over a simple command in-
terface. The interface is listening on the UART interface.
The following sections describe the protocol transported on
the UART interface between the LMX9838 and the host in
command mode (see
Figure 7
). In Transparent mode, no data
framing is necessary and the device does not listen for com-
mands.
15.1 FRAMING
The connection is considered “Error free”. But for packet
recognition and synchronization, some framing is used.
All packets sent in both directions are constructed per the
model shown in
Table 16
.
15.1.1 Start and End Delimiter
The “STX” char is used as start delimiter: STX = 0x02. ETX =
0x03 is used as end delimiter.
15.1.2 Packet Type ID
This byte identifies the type of packet. See
Table 17
for de-
tails.
15.1.3 Opcode
The opcode identifies the command to execute. The opcode
values can be found within the “LMX9838 Software User’s
Guide” included within the LMX9838 Evaluation Board.
15.1.4 Data Length
Number of bytes in the Packet Data field. The maximum size
is defined with 333 data bytes per packet.
15.1.5 Checksum:
This is a simple Block Check Character (BCC) checksum of
the bytes “Packet type”, “Opcode” and “Data Length”. The
BCC checksum is calculated as low byte of the sum of all
bytes (e.g., if the sum of all bytes is 0x3724, the checksum is
0x24).
30027907
FIGURE 7. Bluetooth Functionality
TABLE 16. Package Framing
Start
Delimiter
Packet
Type ID
Opcode
Data
Length
Check
sum
Packet
Data
End
Delimiter
1 Byte
1 Byte
1 Byte
2 Bytes
1 Byte
<Data Length>
Bytes
1 Byte
- - - - - - - - - - - - - Checksum - - - - - - - - - - - - -
15
www.national.com
L
相關PDF資料 |
PDF描述 |
|---|---|
| LNBEH21 | LNB SUPPLY AND CONTROL IC WITH STEP-UP CONVERTER AND IC INTERFACE |
| LNBEH21PD | LNB SUPPLY AND CONTROL IC WITH STEP-UP CONVERTER AND IC INTERFACE |
| LNBEH21PD-TR | LNB SUPPLY AND CONTROL IC WITH STEP-UP CONVERTER AND IC INTERFACE |
| LNBK10 | LNB Supply And Control Voltage Regulator (Parallel Interface)(LNB 電源及控制電壓穩壓器（并行接口）) |
| LP2950L-XX-T92-K | 100 mA LOW-DROPOUT VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX9838SBX/NOPB | 功能描述:藍牙/802.15.1 模塊 RoHS:否 制造商:Murata Wireless Solutions 類:1 頻帶:2402 MHz to 2480 MHz 靈敏度:- 92 dBm 數據速率: 工作電源電壓:2.2 V to 3.3 V 輸出功率: 接口類型:PCM, UART 天線連接器類型:Chip 最大工作溫度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm |
| LMXA301 | 制造商:Maglite 功能描述:3 Cell Lamp 制造商:MAG 功能描述:MAG 3 CELL LAMP, FOR USE WITH: MAG D CELL FLASHLIGHT 29-2000, MAG D CELL FLASHLIGHT 29-2010 制造商:Magnecraft 功能描述:MAGLITE LMXA301 LAMPS 3 CELL |
| LMXA301L | 制造商:MAG-LITE 功能描述: |
| LMXA401 | 制造商:Maglite 功能描述:4 Cell Lamp 制造商:MAG 功能描述:MAGLITE LMXA401 LAMPS 4 CELL 制造商:MAG 功能描述:MAG 4 CELL LAMP, FOR USE WITH: MAG D CELL FLASHLIGHT 29-2015, MAG D CELL FLASHLIGHT 29-2020 |
| LMXA401L | 制造商:MAG-LITE 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。