- 您現在的位置：買賣IC網 > PDF目錄385493 > LMX5001VBC (NATIONAL SEMICONDUCTOR CORP) Dedicated Bluetooth Link Controller PDF資料下載
參數資料
| 型號： | LMX5001VBC |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Dedicated Bluetooth Link Controller |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PQFP48 |
| 封裝： | TQFP-48 |
| 文件頁數： | 5/13頁 |
| 文件大?。?/td> | 198K |
| 代理商： | LMX5001VBC |
(Continued)
tooth radio. It also provides the following functions (under the
control of either a Link Management Controller, or a Host
processor performing Link Management Control functions):
Receive Data and Clock recovery
Access Code correlation
Frame/Slot Counters
Radio control (LMX3162)
Radio Signal Strength Indication (RSSI)
DC Offset compensation
Data transmission and receiving
Link Management Controller communication (LCI)
Power management
Encryption
LMX5001 COMMAND SET
In order to support the range of Bluetooth communication
modes, the LMX5001 has the ability to implement the follow-
ing commands from the Link Management Controller:
Slave Receive with Continuous Correlation
Slave Receive with Windowed Correlation
Slave Transmit
Master Receive
Master Transmit
Change to Master Clock
Change to Slave Clock
Power Down
Slave Receive with Windowed Correlation, Encryption
Enabled
Slave Transmit, Encryption Enabled
Master Receive, Encryption Enabled
Master Transmit, Encryption Enabled
The LMX5001 can also be placed into an Idle State by the
Link Management Controller asserting SYSLOAD. SYS-
LOAD also start the system load process. During this pro-
cess, the transfer of information between LMX5001 Link
Controller and the Link Management Controller takes place.
The interface between the two is Link Controller Interface
(LCI). The formatting of the Command Set, along with Con-
figuration and Status data, sent via the LCI is further detailed
in the LCI sections of this Datasheet.
RECEIVE DATA AND CLOCK RECOVERY
Since Bluetooth is based on a packetized, wireless commu-
nications protocol, it is necessary to frame timing from the re-
ceived packets, before the data itself can be recovered.Also,
since Bluetooth supports both point-to-point and point-to-
multipoint connection, it is also necessary to establish
whether the received packet is addressed to the unit in ques-
tion.
In receive mode, the LMX5001 receives samples from the
LMX3162 at 8 times the Bluetooth Symbol rate (i.e., 8
Mbps). This ensures a +/- 1/8 bit accuracy for receive data
and frame/slot clocking. If the unit in question is operating as
a Slave, then the Slave (Frame/Slot) Counter is updated us-
ing the recovered frame/slot clock upon successful Access
Code correlation.
The received samples are shifted into a 512 sample Buffer in
the correlator. The length of this buffer is fixed to enable the
correlation of a 64-bit Sync Word (8x oversampled) of the
Access Code.
DATA TRANSMISSION AND RECEIVING
Bluetooth data is transferred via a serial interface (LCI) with
the Link Management Controller. The transferred data is bro-
ken down to 8-bit packets. The LCI then uses a 10-bit pack-
age to send each of these 8-bit packets using a big-endian
mode.
The big-endian mode is illustrated in the Figure 2 below:
ACCESS CODE CORRELATION
Access Code Correlation is performed to establish whether a
packet’s payload is intended for the unit in question.
The Access Code to be correlated against the incoming Re-
ceive Data is passed to the LMX5001 from the Link Manage-
ment Controller via the LCI. It is then stored in a 64-bit AC
Buffer in the LMX5001.
The AC Buffer is then correlated with the incoming Receive
Data (stored in the RX Buffer) and the maximum correlation
achieved is transferred to the Correlation Max Buffer.
The Correlation Max is then compared with the contents of
the AC (Access Code) Threshold Buffer, to determine
whether the incoming Access Code sufficiently matches the
unit in question. If the Correlation Max exceeds the AC
Threshold, then the Control Registers “CORR” flag is
cleared, to indicate a correlation.
EXTERNAL CRYSTALS
There are two external crystals, one running at 16 MHz
(
±
10 ppm) and the other at 128 kHz (
±
125 ppm). The higher
rate crystal is used to drive the Bluetooth native clock in nor-
mal mode. This clock is also used as the Link Management
Controller clock input. The lower rate crystal is used when
the Bluetooth unit is in low power mode. In this mode, the
higher rate crystal is shut down so is the Link Management
Controller. Leaving only the lower rate crystal running to up-
date the internal Bluetooth native clock.
FRAME/SLOT COUNTERS
The LMX5001 maintains an internal counter. It is 28 bits in
length, to support the Bluetooth requirement for 2
27
-1 slots.
The Bluetooth slot number is generated based on this
counter. It is also the basis for the Link Management firm-
ware to update its implementation of the Bluetooth Master
and Slave Counters. This clock is in half Bluetooth slot inter-
vals (312.5 μs).
LMX5001 LINK CONTROLLER INTERFACE (LCI)
All Host/Link Management Control of the LMX5001 (and
LMX3162) takes place via the serial LCI.
The signals associated with this port are:
SYSLOAD
SYSTICK
DS101340-3
FIGURE 2. Big-endian Data Convention
L
www.national.com
5
相關PDF資料 |
PDF描述 |
|---|---|
| LNH6644MAX | 3V, Low Power, 130MHz, 75mA Rail-to-Rail Output Amplifiers |
| LP2957 | 5V Low-Dropout Regulator for μP Applications(μP應用的5V低壓差穩壓器) |
| LP2957A | |
| LP2957AIS | 5V Low-Dropout Regulator for P Applications |
| LP2957AIT | 5V Low-Dropout Regulator for P Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX5080 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PLLatinum⑩ 2.7 GHz Low Power Dual Modulus Prescaler for RF Personal Communications |
| LMX5080M | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PLLatinum⑩ 2.7 GHz Low Power Dual Modulus Prescaler for RF Personal Communications |
| LMX5080MX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:PLLatinum⑩ 2.7 GHz Low Power Dual Modulus Prescaler for RF Personal Communications |
| LMX5251SQX/NOPB | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| LMX5252LQ/HALF | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。