- 您現在的位置：買賣IC網 > PDF目錄384601 > LM95214 (National Semiconductor Corporation) Quad Remote Diode and Local Temperature Sensor with SMBus Interface PDF資料下載
參數資料
| 型號： | LM95214 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Quad Remote Diode and Local Temperature Sensor with SMBus Interface |
| 中文描述： | 四遠程二極管與本地溫度傳感器，帶有SMBus接口 |
| 文件頁數： | 35/38頁 |
| 文件大?。?/td> | 448K |
| 代理商： | LM95214 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁
AMD Opteron
AMD Sempron
1.008
1.008
1.00261
1.096
0.93
3.1.3 Compensating for Different Non-Ideality
In order to compensate for the errors introduced by non-ide-
ality, the temperature sensor is calibrated for a particular
processor. National Semiconductor temperature sensors are
always calibrated to the typical non-ideality and series resis-
tance of a given transistor type. The LM95214 is calibrated
for the non-ideality factor and series resistance values of the
MMBT3904 transistor without the requirement for additional
trims. When a temperature sensor calibrated for a particular
thermal diode type is used with a different thermal diode type,
additional errors are introduced.
Temperature errors associated with non-ideality of different
processor types may be reduced in a specific temperature
range of concern through use of software calibration. Typical
Non-ideality specification differences cause a gain variation
of the transfer function, therefore the center of the tempera-
ture range of interest should be the target temperature for
calibration purposes. The following equation can be used to
calculate the temperature correction factor (T
) required to
compensate for a target non-ideality differing from that sup-
ported by the LM95214.
(7)
where
The correction factor should be directly added to the temper-
ature reading produced by the LM95214. For example when
using the LM95214, with the 3904 mode selected, to measure
a AMD Athlon processor, with a typical non-ideality of 1.008,
for a temperature range of 60 °C to 100 °C the correction fac-
tor would calculate to:
η
S
= LM95214 non-ideality for accuracy specification
η
PROCESSOR
= Processor thermal diode typical non-ideality
T
CR
= center of the temperature range of interest in °C
(8)
Therefore, 1.75°C should be subtracted from the temperature
readings of the LM95214 to compensate for the differing typ-
ical non-ideality target.
3.2 PCB LAYOUT FOR MINIMIZING NOISE
30006117
FIGURE 10. Ideal Diode Trace Layout
In a noisy environment, such as a processor mother board,
layout considerations are very critical. Noise induced on
traces running between the remote temperature diode sensor
and the LM95214 can cause temperature conversion errors.
Keep in mind that the signal level the LM95214 is trying to
measure is in microvolts. The following guidelines should be
followed:
1.
V
should be bypassed with a 0.1 μF capacitor in
parallel with 100 pF. The 100 pF capacitor should be
placed as close as possible to the power supply pin. A
bulk capacitance of approximately 10 μF needs to be in
the near vicinity of the LM95214.
2.
A 100 pF diode bypass capacitor is recommended to filter
high frequency noise but may not be necessary. Make
sure the traces to the 100 pF capacitor are matched.
Place the filter capacitors close to the LM95214 pins.
3.
Ideally, the LM95214 should be placed within 10 cm of
the Processor diode pins with the traces being as
straight, short and identical as possible. Trace resistance
of 1
Ω
can cause as much as 0.62°C of error. This error
can be compensated by using simple software offset
compensation.
4.
Diode traces should be surrounded by a GND guard ring
to either side, above and below if possible. This GND
guard should not be between the D+ and D lines. In the
event that noise does couple to the diode lines it would
be ideal if it is coupled common mode. That is equally to
the D+ and D lines.
5.
Avoid routing diode traces in close proximity to power
supply switching or filtering inductors.
6.
Avoid running diode traces close to or parallel to high
speed digital and bus lines. Diode traces should be kept
at least 2 cm apart from the high speed digital traces.
7.
If it is necessary to cross high speed digital traces, the
diode traces and the high speed digital traces should
cross at a 90 degree angle.
8.
The ideal place to connect the LM95214's GND pin is as
close as possible to the Processors GND associated with
the sense diode.
9.
Leakage current between D+ and GND and between D+
and D should be kept to a minimum. Thirteen nano-
amperes of leakage can cause as much as 0.2°C of error
in the diode temperature reading. Keeping the printed
circuit board as clean as possible will minimize leakage
current.
Noise coupling into the digital lines greater than 400 mVp-p
(typical hysteresis) and undershoot less than 500 mV below
GND, may prevent successful SMBus communication with
the LM95214. SMBus no acknowledge is the most common
symptom, causing unnecessary traffic on the bus. Although
the SMBus maximum frequency of communication is rather
low (100 kHz max), care still needs to be taken to ensure
proper termination within a system with multiple parts on the
bus and long printed circuit board traces. An RC lowpass filter
with a 3 dB corner frequency of about 40 MHz is included on
the LM95214's SMBCLK input. Additional resistance can be
added in series with the SMBDAT and SMBCLK lines to fur-
ther help filter noise and ringing. Minimize noise coupling by
keeping digital traces out of switching power supply areas as
well as ensuring that digital lines containing high speed data
communications cross at right angles to the SMBDAT and
SMBCLK lines.
35
www.national.com
L
相關PDF資料 |
PDF描述 |
|---|---|
| LM95214CISD | Quad Remote Diode and Local Temperature Sensor with SMBus Interface |
| LM95214CISDX | Quad Remote Diode and Local Temperature Sensor with SMBus Interface |
| LM95221CIMM | Dual Remote Diode Digital Temperature Sensor with SMBus Interface |
| LM95221CIMMX | Dual Remote Diode Digital Temperature Sensor with SMBus Interface |
| LM95221 | Dual Remote Diode Digital Temperature Sensor with SMBus Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM95214CISD | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95214CISD/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95214CISDX | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95214CISDX/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM95214EB/NOPB | 功能描述:溫度傳感器開發工具 LM95214EVAL BOARD RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
發布緊急采購，3分鐘左右您將得到回復。