參數資料
型號： LM95214
廠商： National Semiconductor Corporation
元件分類： 溫度/濕度傳感器
英文描述： Quad Remote Diode and Local Temperature Sensor with SMBus Interface
中文描述： 四遠程二極管與本地溫度傳感器，帶有SMBus接口
文件頁數： 17/38頁
文件大?。?/td> 448K
代理商： LM95214
30006111
(b) Serial Bus Write to the Internal Command Register
(c) Serial Bus Read from a Register with the Internal Command Register preset to desired value.
30006114
(d) Serial Bus Write followed by a Repeat Start and Immediate Read
FIGURE 8. SMBus Timing Diagrams
1.12 SERIAL INTERFACE RESET
In the event that the SMBus Master is RESET while the
LM95214 is transmitting on the SMBDAT line, the LM95214
must be returned to a known state in the communication pro-
tocol. This may be done in one of two ways:
1.
When SMBDAT is LOW, the LM95214 SMBus state
machine resets to the SMBus idle state if either SMBDAT
or SMBCLK are held low for more than 35ms (t
TIMEOUT
).
Note that according to SMBus specification 2.0 all
devices are to timeout when either the SMBCLK or
SMBDAT lines are held low for 25-35ms. Therefore, to
insure a timeout of all devices on the bus the SMBCLK
or SMBDAT lines must be held low for at least 35ms.
2.
When SMBDAT is HIGH, have the master initiate an
SMBus start. The LM95214 will respond properly to an
SMBus start condition at any point during the
communication. After the start the LM95214 will expect
an SMBus Address address byte.
1.13 ONE-SHOT CONVERSION
The One-Shot register is used to initiate a round of conver-
sions and comparisons when the device is in standby mode,
after which the device returns to standby. This is not a data
register and it is the write operation that causes the one-shot
conversion. The data written to this address is irrelevant and
is not stored. A zero will always be read from this register. All
the channels that are enabled in the Channel Enable Register
will be converted once and the TCRIT1, TCRIT2 and
TCRIT3 pins will reflect the comparison results based on this
round of conversion results of the channels that are not
masked.
2.0 LM95214 Registers
Command register selects which registers will be read from or written to. Data for this register should be transmitted during the
Command Byte of the SMBus write communication.
P7
P6
P5
P4
P3
P2
P1
P0
Command Byte
17
www.national.com
L
相關PDF資料
PDF描述
LM95214CISD Quad Remote Diode and Local Temperature Sensor with SMBus Interface
LM95214CISDX Quad Remote Diode and Local Temperature Sensor with SMBus Interface
LM95221CIMM Dual Remote Diode Digital Temperature Sensor with SMBus Interface
LM95221CIMMX Dual Remote Diode Digital Temperature Sensor with SMBus Interface
LM95221 Dual Remote Diode Digital Temperature Sensor with SMBus Interface
相關代理商/技術參數
參數描述
LM95214CISD 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM95214CISD/NOPB 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM95214CISDX 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM95214CISDX/NOPB 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM95214EB/NOPB 功能描述:溫度傳感器開發工具 LM95214EVAL BOARD RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*