參數資料
型號： LM5046MHX
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, 540 kHz SWITCHING FREQ-MAX, PDSO28
封裝： TSSOP-28
文件頁數： 22/32頁
文件大?。?/td> 888K
代理商： LM5046MHX
301478103
FIGURE 25. Using a Low Side Gate Driver to Augment Gate Drive Strength
Printed Circuit Board Layout
The LM5046 current sense and PWM comparators are very
fast and respond to short duration noise pulses. The compo-
nents at the CS, COMP, SLOPE, RAMP, SS, SSSR, RES,
UVLO, OVP, RD1, RD2, and RT pins should be physically
close as possible to the IC, thereby minimizing noise pickup
on the PC board trace inductance. Eliminating or minimizing
via’s in these critical connections are essential. Layout con-
sideration is critical for the current sense filter. If a current
sense transformer is used, both leads of the transformer sec-
ondary should be routed to the sense filter components and
to the IC pins. The ground side of the transformer should be
connected via a dedicated PC board trace to the AGND pin,
rather than through the ground plane. If the current sense cir-
cuit employs a sense resistor in the drive transistor source,
low inductance resistors should be used. In this case, all the
noise sensitive, low-current ground trace should be connect-
ed in common near the IC, and then a single connection made
to the power ground (sense resistor ground point).
The gate drive outputs of the LM5046 should have short, di-
rect paths to the power MOSFETs in order to minimize in-
ductance in the PC board. The boot-strap capacitors required
for the high side gate drivers should be located very close to
the IC and connected directly to the BST and HS pins. The
VCC and REF capacitors should also be placed close to their
respective pins with short trace inductance. Low ESR and
ESL ceramic capacitors are recommended for the boot-strap,
VCC and the REF capacitors. The two ground pins (AGND,
PGND) must be connected together directly underneath the
IC with a short, direct connection, to avoid jitter due to relative
ground bounce.
Application Circuit Example
The following schematic shows an example of a 100W phase-
shifted full-bridge converter controlled by LM5046. The oper-
ating input voltage range is 36V to 75V, and the output voltage
is 3.3V. The output current capability is 30 Amps. The con-
verter is configured for current mode control with external
slope compensation. An auxiliary winding is used to raise the
VCC voltage to reduce the controller power dissipation.
29
www.national.com
LM5046
相關PDF資料
PDF描述
LM5067SDX-2 2-CHANNEL POWER SUPPLY SUPPORT CKT, DSO10
LM5067SD-2 2-CHANNEL POWER SUPPLY SUPPORT CKT, DSO10
LM555H PULSE; RECTANGULAR, TIMER, MBCY8
LM555H/883B PULSE; RECTANGULAR, TIMER, MBCY8
LM565H/883B PHASE LOCKED LOOP, MBCY10
相關代理商/技術參數
參數描述
LM5046MHX/NOPB 功能描述:電流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
LM5046SQ 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM5046 Phase-Shifted Full-Bridge PWM Controller with Integrated MOSFET Drivers
LM5046SQ/NOPB 功能描述:電流型 PWM 控制器 Phase-Shifted Full- Bridge PWM Cntrlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
LM5046SQX 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM5046 Phase-Shifted Full-Bridge PWM Controller with Integrated MOSFET Drivers
LM5046SQX/NOPB 功能描述:IC PWM CTRLR FULL BRIDG 28LLP RoHS:是 類別:集成電路 (IC) >> PMIC - AC-DC 轉換器，離線開關 系列:PowerWise® 標準包裝:1 系列:FPS™ 輸出隔離:隔離 頻率范圍:61kHz ~ 73kHz 輸入電壓:8 V ~ 26 V 輸出電壓:650V 功率（瓦特）:12W 工作溫度:-40°C ~ 115°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-MDIP 包裝:Digi-Reel® 其它名稱:FSL206MRBNFSDKR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*