- 您現在的位置：買賣IC網 > PDF目錄30737 > LC89058W-E SPECIALTY CONSUMER CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | LC89058W-E |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| 封裝： | 7 X 7 MM, SQFP-48 |
| 文件頁數： | 13/46頁 |
| 文件大?。?/td> | 284K |
| 代理商： | LC89058W-E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
LC89058W-E
No.A1056-20/64
10.1.3 Switching between master clock and clock source
The RMCK, RBCK, and RLRCK (hereunder, R system), and the SBCK and SLRCK (hereunder, S system) clock
sources can be selected between the following two master clocks.
(1) PLL source (512fs)
(2) XIN source (12.288MHz or 24.576MHz)
Clock source switching is to set with the R and S systems interlocked. This setting is carried out with OCKSEL.
The clock source is automatically switched to the PLL or XIN clock by locking/unlocking the PLL. The clock source
can be switched to XIN with OCKSEL, regardless of the PLL status.
Table 10.1: Relationship between Clock Source Switch Commands and Clock Sources when PLL Locked/Unlocked
R System Clock Source
S System Clock Source
OCKSEL
Locked
Unlocked
Locked
Unlocked
0
PLL
XIN
PLL
XIN
1
XIN
The PLL status can be always monitored with RERR even after switching to the XIN source. Moreover, the processed
information can be read with the microcontroller interface regardless of the PLL status.
10.1.4 Points to notice about switching clock source while PLL is locked
It is necessary to set the oscillation amplifier to the continuous operation mode at the same time with AMPOPR [1:0]
to do the clock switch to the XIN source with OCKSEL when the oscillation amplifier has stopped in the state where
the PLL is locked. The clock is not output when switching to the XIN clock source without executing this setting.
In the state where the PLL is locked, if the clock is switched to XIN source with OCKSEL while the oscillator
amplifier is stopped, RERR is temporarily outputs an error (high level) indication. When switched to XIN source, the
oscillator amplifier is switched to the operating state at the same time.
RERR is temporality outputs an error (H level) indication when the oscillation amplifier switches from the stop
condition to the continuous mode. Consequently the input fs calculation restarts. At this time, the previous fs
calculation value is reset and compared with the newly calculated fs value. Then those two values are found not
identical, that’s why the error is temporarily issued.
相關PDF資料 |
PDF描述 |
|---|---|
| LC89058W-E | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC8905V | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LC8910 | TRANSMITTER/RECEIVER IC, PDIP24 |
| LC8913 | TRANSMITTER/RECEIVER IC, PDIP40 |
| LC8912 | TRANSMITTER/RECEIVER IC, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC8905V | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Digital Audio Interface Receiver |
| LC89060 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6-Bit Video D/A Converters |
| LC89060M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6-Bit Video D/A Converters |
| LC89066 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6-Bit Video A/D Converters |
| LC89066M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6-Bit Video A/D Converters |
發布緊急采購，3分鐘左右您將得到回復。