- 您現在的位置：買賣IC網 > PDF目錄2082 > LA42032-E (ON Semiconductor)IC AF POWER AMP 5WX2CH SIP13H PDF資料下載
參數資料
| 型號： | LA42032-E |
| 廠商： | ON Semiconductor |
| 文件頁數： | 4/7頁 |
| 文件大小： | 0K |
| 描述： | IC AF POWER AMP 5WX2CH SIP13H |
| 標準包裝： | 20 |
| 類型： | AB 類 |
| 輸出類型： | 2 通道（立體聲） |
| 在某負載時最大輸出功率 x 通道數量： | 5W x 2 @ 8 歐姆 |
| 電源電壓： | 5.5 V ~ 15 V |
| 特點： | 靜音，短路和熱保護，待機 |
| 安裝類型： | 通孔 |
| 供應商設備封裝： | 13-SIPH |
| 封裝/外殼： | 13-SIP 裸露焊盤 |
| 包裝： | 管件 |
4
INDUSTRIAL TEMPERATURERANGE
IDT72V73260 3.3V TIME SLOT INTERCHANGE
DIGITAL SWITCH 16,384 x 16,384
PIN DESCRIPTION
SYMBOL
NAME
I/O
DESCRIPTION
A0-15
Address 0 to 15
I
These address lines access all internal memories.
C32i
Clock
I
Serial clock for shifting data in/out on the serial data stream. This input accepts a 32.768 MHz clock.
CS
Chip Select
I
This active LOW input is used by a microprocessor to activate the microprocessor port of IDT72V73260.
D0-15
Data Bus 0-15
I/O
These pins are the data bits of the microprocessor port.
DS
Data Strobe
I
This active LOW input works in conjunction with
CS to enable the read and write operations and sets the
data bus lines (D0-D15).
DTA
Data Transfer
O
Indicates that a data bus transfer is complete. When the bus cycle ends, this pin drives HIGH and then goes
Acknowledgment
high-impedance, allowing for faster bus cycles with a weaker pull-up resistor. A pull-up resistor is required
to hold a HIGH level when the pin is in high-impedance.
FE
Frame Evaluation
I
This input can be used to measure delay in the data path by comparing the frame pulse, F32i, with this input.
F32i
Frame Pulse
I
This input accepts and automatically identifies frame synchronization signals formatted according to
ST-BUSand GCI specifications.
GND
Ground
Ground Rail
ODE
Output Drive Enable
I
This is the output enable control for the TX serial outputs. When the ODE input is LOW and the Output Stand
By bit of the Control Register is LOW, all TX outputs are in a high-impedance state. If this input is HIGH, the TX
output drivers are enabled. However, each channel may still be put into a high-impedance state by using the
per-channel control bits in the Connection Memory.
RESET
Device Reset
I
This input puts the IDT72V73260 into a reset state that clears the device internal counters, registers and
brings TX0-31 and D0-D15 into a high-impedance state. The
RESET pin must be held LOW for a minimum
of 20ns to properly reset the device.
R/
W
Read/Write
I
This input controls the direction of the data bus lines (D0-D15) during a microprocessor access.
RX0-31
DataStream
I
Serial data input stream. These streams have a data rate of 32.768Mb/s.
Input 0 to 31
TCK
Test Clock
I
Provides the clock to the JTAG test logic.
TDI
Test Serial Data In
I
JTAG serial test instructions and data are shifted in on this pin. This pin is pulled HIGH by an internal pull-up
when not driven.
TDO
Test Serial Data Out
O
JTAG serial data is output on this pin on the falling edge of TCK. This pin is held in high-impedance state
when JTAG scan is not enabled.
TMS
Test Mode Select
I
JTAG signal that controls the state transitions of the TAP controller. This pin is pulled HIGH by an internal
pull-up when not driven.
TRST
TestReset
I
Asynchronously initializes the JTAG TAP controller by putting it in the Test-Logic-Reset state. This pin is
pulled by an internal pull-up when not driven. This pin should be pulsed LOW on power-up, or held LOW,
to ensure that the IDT72V73260 is in the normal functional mode.
TX0-15
TX Output 0 to 15
O
Serial data output stream. These streams have a data rate of 32.768Mb/s.
(Three-StateOutputs)
TX16-31/ TX Output 16 to 31/
O
When all 32 output streams are selected via Control Register, these pins are the output streams TX16 to TX31
OEI0-15
OutputEnable
and operate at 32.768Mb/s. When output enable function is selected, these pins reflect the active or
Indication 0 to 15
high-impedance status for the corresponding output stream Output Enable Indication0-15.
(Three-StateOutputs)
VCC
+3.3 Volt Power Supply.
相關PDF資料 |
PDF描述 |
|---|---|
| LA4425A-E | IC AUDIO POWER AMP 5W TO-126ML |
| LA4425PV-MPB-H | IC AUDIO POWER AMP 5W 44SSOP |
| LA4625-E | IC BTL PWR AMP 13.5W 2CH SIP14HZ |
| LA4708N-E | IC BTL PWR AMP 20W 2CH SIP18H |
| LDS6000NQGI | IC SENSOR TCH PURETOUCH 28VFQFPN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA42032L-E | 制造商:Sony Semiconductor Solutions Division 功能描述: |
| LA42051 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Audio Output for TV Application 5W×1ch Power Ampilfier |
| LA42052 | 制造商:SANYO Semiconductor Co Ltd 功能描述:5W Stereo Sanyo IC 13-Pin SIP-Hs |
| LA42052-E | 功能描述:音頻放大器 POWER AMPLIFIER RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LA42052HK-E | 制造商:Sony Semiconductor Solutions Division 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。