- 您現在的位置：買賣IC網 > PDF目錄383255 > L9929 (意法半導體) SPI CONTROLLED H-BRIDGE PDF資料下載
參數資料
| 型號： | L9929 |
| 廠商： | 意法半導體 |
| 英文描述： | SPI CONTROLLED H-BRIDGE |
| 中文描述： | 可控的SPI H橋 |
| 文件頁數： | 11/23頁 |
| 文件大?。?/td> | 629K |
| 代理商： | L9929 |
11/23
L9929
4
Diagnostic
The Diagnosis-Mode can be selected between SPI-Diagnosis and Status-Flag Diagnosis.
The choise of the Diagnosis-Mode is selected by the voltage-level on pin 12 (DMS Diagnosis Mode Selection).
DMS = GND Status-Flag
DMS = Vcc SPI-Diagnostic
For the connection of pins SI, SO, SS and SCK/SF see Fig. 13 respectively Fig. 14.
4.1
The Status-Flag showes the condition tristate“.
At the following fault-cases the output-stages switches in tristate and set the status-flag from high to low.
- Short circuit of OUT1 or OUT2 against V
S
or GND
- Short circuit between OUT1 and OUT2
- Overcurrent
- Overtemperature
- Undervoltage on V
S
In cause of short circuit or overcurrent, the fault will be stored.
The output stage switches in tristate and the status-flag is set from high level to low-level if the specified value
is exceeded.
If the voltage level changes from high to low on DI or from low to high on EN, the output stage switches on again
and the status-flag is reset to high-level.
In cause of overtemperature the fault will be stored.
The output stage switches in tristate and the status-flag is set from high level to low-level if the specified value
is exceeded.
If the voltage level changes from high to low on DI or from low to high on EN, the output stage switches on again
and the status-flag is reset to high-level.
In cause of undervoltage on V
Batt
the output stage switches in tristate and the status-flag is set from high level
to low-level if the specified value is fallen. If the voltage has risen about the specified value again, the output
stage switches on again and the status-flag is reset to high-level.
The maximum current which can flow under normal operating conditions is limited to typical I
max.
= 8.6A .
When the maximum current value is reached, the output stages are switched tristate for a fixed time.
According to the time-constant the current decreases exponentially until the next switch-on occurs.
At the end if the fixed time the output stage switches on again and the status-flag is reset to high-level.
Status-Flag
5
SPI-INTERFACE
5.1
The serial SPI interface establishes a communication link between L9929 and the systems microcontroller.
L9929 always operates in slave mode whereas the controller provides the master function.
The maximum baud rate is 2 MBaud (200pF).
Applying an active slave select signal at SS L9929 is selected by the SPI master. SI is the data input (Slave In),
SO the data output (Slave Out). Via SCK (Serial Clock Input) the SPI clock is provided by the master.
In case of inactive slave select signal (High) the data output SO goes into tristate.
General Discription
相關PDF資料 |
PDF描述 |
|---|---|
| L9929XP | SPI CONTROLLED H-BRIDGE |
| L9935 | TWO-PHASE STEPPER MOTOR DRIVER |
| L9937 | FULL BRIDGE MOTOR DRIVER |
| L9947 | QUAD HALF-BRIDGE AND SINGLE HIGH-SIDE DRIVER |
| L9947S | QUAD HALF-BRIDGE AND SINGLE HIGH-SIDE DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9929XP | 制造商:STMicroelectronics 功能描述: |
| L992CG-1 | 制造商:Thomas & Betts 功能描述:3/4 LR COND BODY W/ COVER & GASKET, |
| L9930 | 制造商:STMicroelectronics 功能描述:DUAL FULL BRIDGE 11PIN MULTIWATT V - Rail/Tube |
| L9930PD | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9930PD13TR | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。