- 您現在的位置：買賣IC網 > PDF目錄43901 > L8229 (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 1.5 A, PDSO24 PDF資料下載
參數資料
| 型號： | L8229 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1.5 A, PDSO24 |
| 封裝： | LEAD FREE, SSO-24 |
| 文件頁數： | 10/42頁 |
| 文件大?。?/td> | 858K |
| 代理商： | L8229 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Obsolete
Product(s)
- Obsolete
Product(s)
L6219_8 mode
L8229
7
L6219_8 mode
A second configuration of the device is achieved when PROG1 and PROG2 pins (pin 7 and
18) are asserted to 01. The device is now configured into the L6219_8 configuration. This
device mode function is similar to L6219_HI, but with the possibility of using 8 current levels
instead of 4, to implement a more accurate microstepping function and with the possibility to
set a mixed decay for recirculation current. The remaining functionalities are identical to
L6219_HI mode.
7.1
8 Level Current Setting
This setting is achieved by using pin 8 (STB) as a strobe for latching the current setting
control inputs. The rising edge of STB will latch the I01, I11 and I12 inputs for decoding
current levels settings for Bridge 1. Similarly the falling edge will latch the I01, I11 and I12
inputs for decoding current levels settings for Bridge 2.
In order to allow a good similitude to sine drive, the levels set by the input pins are not
equally spaced but are choosen to approximate a sinusoidal wave.
On power up, the device is by default into a no current drive state for both H Bridges and will
start driving only upon the rising or falling edges of STB.
7.2
Mixed Decay
VREFCOM input (pin 15) is the reference voltage for both bridges while VREFDEC input
(pin 11) is a voltage reference for decay control. When the current setting is set from an
higher level to a lower level, the device can be set to perform:
1.
Slow decay (current is recirculated throught the low side drivers) when VREFDEC > 0.94Vcc.
2.
A mix of Fast followed by Slow decay when 0.33Vcc < VREFDEC < 0.94Vcc.
3.
Fast decay (current is recirculated from Sense to Vs) when VREFDEC < 0.33Vcc.
In case 2, VREFDEC voltage is compared with the RC discharging voltage during the Toff
duration. Until the RC voltage is above VREFDEC there will be fast decay: the bridge
outputs will be driven to enable recirculation from Rsense to VS. For RC voltages below
VREFDEC, the bridges will be driven to recirculate through the low side drivers. (see
Table 12.
Current levels
STB
I01
I11
I12
Current level
Bridge1
Bridge 2
0
No current
-
00
1
IOUT / Imax=0.22
-
01
0
IOUT / Imax=0.42
-
01
1
IOUT / Imax=0.61
-
10
0
IOUT / Imax=0.77
-
10
1
IOUT / Imax=0.87
-
相關PDF資料 |
PDF描述 |
|---|---|
| L9484 | SWITCHING REGULATOR, 460 kHz SWITCHING FREQ-MAX, PSFM8 |
| L9903 | BRUSH DC MOTOR CONTROLLER, PDSO20 |
| L9903TR | BRUSH DC MOTOR CONTROLLER, PDSO20 |
| L9911B | BRUSH DC MOTOR CONTROLLER, SFM8 |
| L9911A | BRUSH DC MOTOR CONTROLLER, SFM8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L822HW | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
| L822HW-1R0MF | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
| L822HW-1R5MF | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
| L822HW-2R2MF | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
| L822HW-3R3MF | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:HIGH CURRENT MOLDED POWER INDUCTORS |
發布緊急采購，3分鐘左右您將得到回復。