- 您現在的位置：買賣IC網 > PDF目錄383239 > L7250 (意法半導體) 5V & 12V SPINDLE AND VCM MOTORS DRIVER PDF資料下載
參數資料
| 型號： | L7250 |
| 廠商： | 意法半導體 |
| 英文描述： | 5V & 12V SPINDLE AND VCM MOTORS DRIVER |
| 中文描述： | 5V的 |
| 文件頁數： | 39/46頁 |
| 文件大?。?/td> | 478K |
| 代理商： | L7250 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
39/46
L7250
4.3 Negative Voltage Regulator (flyback configuration)
This is the default Negative Voltage Regulator configuration; programming the Test Register is possible to re-
configurate this regulator following the indication present on the next paragraph.
The negative voltage regulator is a fixed frequency switcher intended to provide bias for the MR head preamp.
The NVR consists of an internal triangular wave oscillator, an error amplifier, a comparator and a circuitry to soft
start_up the regulator itself, in conjunction with an external PMOS power device, power diode, inductor, capac-
itor, feedback resistors and compensation network (refer to the block diagram of the negative voltage regulator
including also the external components).
The error amp compares the external voltage feedback to the internal reference (Vbg = 1.25V). The voltage dif-
ference value is scaled by two external resistors. The ratio of these two resistors determines the nominal value
of the regulated negative voltage (the internal reference is set to the bandgap voltage ~1.25V). The error am-
plifier input is available at N_FEED pin and the amplifier output is available at N_COMP pin. The voltage error
gain and the loop compensation can be adjusted by the external components across these two pins. The output
of the error amplifier is compared to an internal triangular wave oscillator to determine the duty cycle of the ex-
ternal PMOS power switch. A voltage clamp is placed on the error amplifier output to limit the maximum duty
cycle. The nominal value of the triangular wave oscillator frequency is 500 kHz (programming the test register
Reg 0FH to ‘00001001’ it is possible to increment the switching frequency to the nominal value of 1Mhz). During
the ON portion of the duty cycle, the PMOS charges an external inductor. During the OFF phase, the inductor
charges a capacitor through an external diode, in a voltage inverter configuration. This architecture avoids any
negative voltage on the L7250 IC pins. Under normal specified load conditions and correct scaling of the ex-
ternal components the regulator circuit should operates in a constant frequency variable duty cycle switch mode
without any cycle slips. The NVR include also a digital soft start_up circuitry in order to limit the in rush current
coming from the power supply when the regulator is turned-on. The NVR is controlled via serial port (using the
Reg. 05H -> b1 the regulator could be turned on and off). During the power-up and power-down phases the
regulator is always off being the serial port in reset status then the VnegEn bit equal to zero. During those phas-
es the N_DRV output driver is in tri-state condition then an external pull-up to assure the Pch off condition must
be considered.
Figure 17. Negative regulator (Flyback configuration) - default configuration
12
N_COMP
10
N_DRV
VCC5
21
VREF25
Vbg
(typ 1.25)
11
N_FEED
R1ext
M 1ext
R2ext
Rcext
Ccext
Cfext
500Khz - 1Mhz
5K
相關PDF資料 |
PDF描述 |
|---|---|
| L7805ABD2T-TR | Precision 1A regulators |
| L7805ACD2T-TR | Precision 1A regulators |
| L7806ABD2T-TR | Precision 1A regulators |
| L7806ACD2T-TR | Precision 1A regulators |
| L7808ABD2T-TR | Precision 1A regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L7250E1.2 | 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L7252E2.6 | 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L725MAG | 制造商:Apex Tool Group 功能描述:TAPE, 1 IN. X 25 FT, 700 SERIES, MAGNETIC END HOOK 制造商:Lufkin 功能描述:TAPE MEASURE, MAGNETIC END HOOK 25FT 1IN; Tape Measure Type:Manual; Measuring Range Max:25ft; Blade Width:1"; Case Color:Orange; Tool Body Material:ABS; Blade Finish:Yellow Clad; Blade Length:25ft ;RoHS Compliant: NA |
| L728 | 制造商:BURNDY 功能描述:L-DIE |
| L7290 | 制造商:CIPS 功能描述:CUTTER OBLIQUE SEMI FLUSH 109MM |
發布緊急采購，3分鐘左右您將得到回復。