參數資料
型號： L7250
廠商： 意法半導體
英文描述： 5V & 12V SPINDLE AND VCM MOTORS DRIVER
中文描述： 5V的
文件頁數： 31/46頁
文件大?。?/td> 478K
代理商： L7250
31/46
L7250
3.8 VCM Ramp Load / Unload System
Figure 11.
The Ramp Load system is designed to allow a microcontrolled assisted constant velocity for ramp loading and
unloading.
VCM Current-Voltage-Bemf monitor circuitry is integrated for the loading or unloading operation. VCM Current-
Voltage-Bemf are converted in digital by a 10 bit AD converter and can be read through the serial port.
3.8.1 Load/Unload operation at power good
When both the 12V and 5V are present, the Load/Unload operation can be assisted by the microcontroller. The
power stage can be driven in both current and voltage mode and the velocity of the Load/Unload operation is
controlled by reading the internal registers that give information regarding the VCM current, voltage and the
Bemf generated by the VCM motion.
The VCM current measurements is done by sending to the AD converter the output of the VCM Current Sense
Ampl.
The VCM voltage is measured by connecting an operational amplifier, with a scaling factor, to the VCMP and
VCMN of the power stage.
The VCM Bemf detection is done using a first amplifier, having a controlled gain, followed by a second opera-
tional amplifier implementing the transfer function necessary to BEMF reconstruction. The programmable gain
of the first operational amplifier it is necessary to consider various coil resistance values related to different ap-
plication.
The BEMF information is carry out on pin VCMBEMF (31) for filtering pourpose (the output impedance is typi-
cally set to 500ohm).
The conversion in digital of these parameters is used by the microcontroller as a feedback to close the velocity
control loop during the ramp loading or unloading operation, and to perform calibrations.
All these signals can enter directly the ADC block (ADCrange bit = 0) or can be scaled to adjust the dynamic
range to the ADC one (ADCRange bit = 1).
The scaling factor is set equal to 2.25 for the ‘Current’, ‘Voltage’, ‘Auxiliary’ input channels, while is set to 1.25
for the ‘Bemf’ input channel.
Rs
VCMN
VCM
VCMP
+A
-A
+
_
VGA
+
_
+
_
_
+
Current
ADC
10 bit
Voltage
Bemf
Sel&start
Gain
Calibration
Procedure
VCM
Predriver
(Sense Ampl)
to
Serial Port
Offset
calibration
CalCoarse
29
Vcontrol
5 MSB from
ADC
Fine calibration
bit from
Serial Port
相關PDF資料
PDF描述
L7805ABD2T-TR Precision 1A regulators
L7805ACD2T-TR Precision 1A regulators
L7806ABD2T-TR Precision 1A regulators
L7806ACD2T-TR Precision 1A regulators
L7808ABD2T-TR Precision 1A regulators
相關代理商/技術參數
參數描述
L7250E1.2 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
L7252E2.6 功能描述:電源開關 IC - 配電 DSD POWER RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
L725MAG 制造商:Apex Tool Group 功能描述:TAPE, 1 IN. X 25 FT, 700 SERIES, MAGNETIC END HOOK 制造商:Lufkin 功能描述:TAPE MEASURE, MAGNETIC END HOOK 25FT 1IN; Tape Measure Type:Manual; Measuring Range Max:25ft; Blade Width:1"; Case Color:Orange; Tool Body Material:ABS; Blade Finish:Yellow Clad; Blade Length:25ft ;RoHS Compliant: NA
L728 制造商:BURNDY 功能描述:L-DIE
L7290 制造商:CIPS 功能描述:CUTTER OBLIQUE SEMI FLUSH 109MM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*