參數資料
型號： L6918AD
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PDSO28
封裝： SO-28
文件頁數： 23/35頁
文件大?。?/td> 431K
代理商： L6918AD
3/35
L6918 L6918A
ABSOLUTE MAXIMUM RATINGS
THERMAL DATA
Symbol
Parameter
Value
Unit
Vcc, VCCDR
To PGND
15
V
VBOOT-VPHASE
Boot Voltage
15
V
VUGATE1-VPHASE1
VUGATE2-VPHASE2
15
V
LGATE1, PHASE1, LGATE2, PHASE2 to PGND
-0.3 to Vcc+0.3
V
VID0 to VID4
-0.3 to 5
V
All other pins to PGND
-0.3 to 7
V
VPHASEx
Sustainable Peak Voltage t<20nS @ 600kHz
26
V
Symbol
Parameter
Value
Unit
Rth j-amb
Thermal Resistance Junction to Ambient
60
°C/ W
Tmax
Maximum junction temperature
150
°C
Tstorage
Storage temperature range
-40 to 150
°C
Tj
Junction Temperature Range
0 to 125
°C
PMAX
Max power dissipation at Tamb=25
°C
2W
L6918A (MASTER) PIN FUNCTION
N.
Name
Description
1
LGATE1
Channel 1 low side gate driver output.
2
VCCDR
LS Mosfet driver supply. 5V or 12V buses can be used.
3
PHASE1
This pin is connected to the Source of the upper mosfet and provides the return path for the
high side driver of channel 1.
4
UGATE1
Channel 1 high side gate driver output.
5
BOOT1
Channel 1 bootstrap capacitor pin. This pin supplies the high side driver. Connect through a
capacitor to the PHASE1 pin and through a diode to Vcc (cathode vs. boot).
6
VCC
Device supply voltage. The operative supply voltage is 12V.
7
GND
All the internal references are referred to this pin. Connect it to the PCB signal ground.
8
COMP
This pin is connected to the error amplifier output and is used to compensate the control
feedback loop.
9
FB
This pin is connected to the error amplifier inverting input and is used to compensate the
voltage control feedback loop.
A current proportional to the sum of the current sensed in both channel is sourced from this pin
(50
A at full load, 70A at the Over Current threshold). Connecting a resistor RFB between
this pin and VSEN pin allows programming the droop effect.
10
VPROG_OUT
Reference voltage output used for voltage regulation.
This pin must be connected together with the slave device VPROG_IN pin.
Filter to SGND with 1nF capacitor (a total 30nF distributed capacitance is allowed).
11
SYNC_OUT
Synchronization output signal. From this pin exits a square - 50% duty cycle - 5Vpp –90 deg
phase shifted wave clock signal that the Slave device PLL locks to.
Connect this pin to the Slave SYNC_IN pin.
12
SLAVE_OK
Open-drain input/output used for start-up and to manage protections as shown in the timing
diagram. Internally pulled-up. Connect together with other IC’s SLAVE_OK pin. Filter with 1nF
capacitor vs. SGND.
相關PDF資料
PDF描述
L6919CD SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28
L6919E SWITCHING CONTROLLER, PDSO28
L6920DTR 1.2 A SWITCHING REGULATOR, PDSO8
L6920D 1.2 A SWITCHING REGULATOR, PDSO8
L6920 1.2 A SWITCHING REGULATOR, PDSO8
相關代理商/技術參數
參數描述
L6918ADTR 功能描述:DC/DC 開關控制器 Prog Multi-Phase Cnt RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6918D 功能描述:DC/DC 開關控制器 Prog Multi-Phase Cnt RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6918DTR 功能描述:DC/DC 開關控制器 Prog Multi-Phase Cnt RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6919 制造商:未知廠家 制造商全稱:未知廠家 功能描述:5 BIT PROGRAMMABLE DUAL-PHASE CONTROLLER WITH DYNAMIC VID MANAGEMENT
L6919C 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:5 BIT PROGRAMMABLE DUAL-PHASE CONTROLLER WITH DYNAMIC VID MANAGEMENT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*