參數資料
型號： L4992
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PQFP32
封裝： TQFP-32
文件頁數： 25/26頁
文件大?。?/td> 296K
代理商： L4992
Synchronous rectification.
Very high efficiency is achieved at high load current with the synchronous rectification technique, which
is particularly advantageous because of the low output voltage. The low-side MOSFET, that is the syn-
chronous rectifier, is selected with a very low on-resistance, so that the paralleled Schottky diode is not
turned on, except for the small time in which neither MOSFET is conducting. The effect is a considerable
reduction of power loss during the recirculation period.
Although the Schottky might appear to be redundant, it is not in a system where a very high efficiency is
required. In fact, its lower threshold prevents the lossy body-diode of the synchronous rectifier MOSFET
from turning on during the above mentioned dead-time. Both conduction and reverse recovery losses are
cut down and efficiency can improve of 1-2% in some cases. Besides a small diode is sufficient since it
conducts for a very short time.
As for the 3.3V section only, the synchronous rectifier is also involved in the 12 V linear regulator opera-
tion (see the relevant section). See also the "Power Management" to see how both synchronous rectifi-
ers are used to ensure zero voltage output in stand-by conditions or in case of overvoltage.
Pulse-skipping operation.
To achieve high efficiency at light load current as well, under this condition the regulators change their
operation (unless this feature is disabled): they abandon PWM and enter the so-called pulse-skipping
mode, in which a single switching cycle takes place every many oscillator periods.
The "light load condition" is detected when the voltage across the external sense resistor (VRsense) does
not exceed 26mV while the high-side MOSFET is conducting. When the reset signal of the output latch
comes from the error summing comparator while VRsense is below this value, it is ignored and the actual
reset is driven as soon as VRsense reaches 26mV. This gives some extra energy that maintains the output
voltage above its nominal value for a while. The oscillator pulses now set the output latch only when the
feedback signal indicates that the output voltage has fallen below its nominal value. In this way, most of
oscillator pulses is skipped and the resulting switching frequency is much lower, as expressed by the fol-
lowing relationship:
fps
= K
Rsense
2
L
Iout Vout
1
Vout
Vin
where K = 3.2
103 and fps is in Hz. As a result,
the losses due to switching and to gate-drive,
which mostly account for power dissipation at low
output power, are considerably reduced.
The +5.1V section can work with the input voltage
very close to the output one, where the current
waveform may be so flat to prevent pulse-skipping
from being activated. To avoid this, the pulse-skip-
ping threshold (of the +5.1V section only) is
roughly halved at low input voltages, as shown in
fig. 3. Under this condition, in the above formula
the constant K becomes 12.8
103.
When in pulse-skipping, the output voltage is
some ten mV higher than in PWM mode, just be-
cause of its mode of operation. If this "load regula-
tion" effect is undesirable for any reason, the pulse
skipping feature can be disabled (see "Power
Management" section) to the detriment of effi-
ciency at light load.
MOSFET’s drivers
To get the gate-drive voltage for the high-side N-channel MOSFET a bootstrap technique is employed. A
capacitor is alternately charged through a diode from the 5V REG5 line when the high-side MOSFET is
OFF and then connected to its gate-source leads by the internal floating driver to turn the MOSFET on.
The REG5 line is used to drive the synchronous rectifier as well, and therefore the use of low-threshold
Vth
Vin
26 mV
13 mV
5.5V 5.8V
6.3V
20V
Figure 3: Pulse-skipping threshold vs. input
voltage (+5.1V section only).
DETAILED FUNCTIONAL DESCRIPTION (continued)
L4992
8/26
相關PDF資料
PDF描述
L5953 1.2 A SWITCHING REGULATOR, 425 kHz SWITCHING FREQ-MAX, PDSO36
L5962 SWITCHING REGULATOR, PDSO36
L5973DD 3.5 A SWITCHING REGULATOR, 280 kHz SWITCHING FREQ-MAX, PDSO8
L5988D 5.6 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16
L5994A 1 A DUAL SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQFP32
相關代理商/技術參數
參數描述
L4993 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low drop voltage regulator
L4993D 功能描述:低壓差穩壓器 - LDO Low drop voltage regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
L4993DTR 功能描述:低壓差穩壓器 - LDO Low drop voltage regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
L4993MD 功能描述:低壓差穩壓器 - LDO Low drop voltage regulator RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
L4993MDTR 功能描述:低壓差穩壓器 - LDO 5V 150mA LW DROP VLT REGULATOR RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*