- 您現在的位置：買賣IC網 > PDF目錄383231 > L3916A (意法半導體) SPEECH AND 14 MEMORY DIALER WITH LED DRIVER PDF資料下載
參數資料
| 型號： | L3916A |
| 廠商： | 意法半導體 |
| 元件分類： | LED驅動器 |
| 英文描述： | SPEECH AND 14 MEMORY DIALER WITH LED DRIVER |
| 中文描述： | 言論和14記憶體，LED驅動撥號器 |
| 文件頁數： | 3/14頁 |
| 文件大小： | 124K |
| 代理商： | L3916A |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
A valid keypad entry is either a single Row con-
nected to a single Column or GND simultaneously
presented to both a single Row and a single Col-
unm.
In its quiescent or standby state, during normal
off-hook operation, either the Rows or the Col-
umns are at logic level 1 (V
DD
). Pulling one input
low enables the on chip oscillator. Keyboard
scanning then begins.
Scanning consists of Rows and Columns alter-
nately switching high through on chip pullups. Af-
ter both a Row and Column key have been de-
tected, the debounce counter is enabled and any
noise (bouncingcontacts, etc) is ignored for a de-
bounce period (TKD) of 32ms. At this time, the
keyboard is sampledand if boththe Row andCol-
umn information are valid, the information is buff-
ered into the LND location. After scanning starts,
the row and column inputs will assume opposite
states.
In the tone mode, if two or more keys in the same
row or if two or morekeys in the samecolumnare
depressed a single tone will be output. The tone
will corresponds to the row or column for which
the two keys were pushed. This feature is for test-
ing purposes,and single tone will not be redialed.
Also in the tone mode, the output tone is continu-
ous in the manual dialing as long as the key is
pushed. The output tone duration follows the Ta-
ble 1. When redialing in the tone mode, each
DTMF output has 100ms duration, and the tone
separation (inter signal delay) is 100ms.
Table 1:
OutputTone Duration
Key-Push Time, T
T<= 32ms
Tone Output
No output, ignored by
one chip phone.
100ms Duration
32ms < = T < = 100ms +
Tkd
T > = 100ms + Tkd
Output Duration = T - Tkd
OSC
Output. Pin 5. Only one pin is needed to connect
the ceramic resonator to the oscillator circuit. The
other end of the resonator is connected to GND
(pin 8). The nominal resonator frequency is
3.579545MHz and any deviation from this stand-
ard is directly reflected in the Tone output fre-
quencies. The ceramic resonator provides the
time reference for all circuit functions. A ceramic
resonator with tolerance of
±
0.25% is recom-
mended
PULSE
Output. Pin 6. This is an output consisting of an
open drain N-Channel device. During on-hook,
pulseoutputpin is in high impedanceand onceoff-
hooked,it will be pulled highby externalresistor.
MODE/PACIFIERTONE
Input (MODE). Pin 7. MODE determines the di-
aler’s default operating mode. When the device is
powered up or the hookswitch input is switched
from on-hook (V
DD
) to off-hook (GND), the default
determines the signalling mode. A V
DD
connec-
tion defaults to tone mode operation and a GND
connectiondefaultsto pulsemode operation.
When dialing in the pulse mode, a softswitch fea-
ture will allow a change to the tone mode when-
ever the * key is depressed. Subsequent* key in-
puts will cause the DTMF code for an * to be
dialed.. The softswitch will only switch from pulse
to tone. After returning to on-hookand back to off-
hook, the phone will be in pulse mode. Redial by
the LND key or the MEM key will repeat the soft-
switch.
Output (PACIFIER TONE). Pin 7. In pulse mode,
all valid key entries activate the pacifier tone. In
tone
mode, any non DTMF entry (FLASH,
PROG, PAUSE,LND, MEM, E1, E2 and E3), acti-
vates the pacifier tone. The pacifier tone provides
audible feedback, confirming that key has been
properly entered and accepted. It is a 500Hz
square wave activated upon acceptance of valid
key input after the 32ms debounce time. The
square wave terminates after a maximum of
75ms or when the valid key is no longer present.
The pacifier tone signal is simultaneously sent to
earphone and the buzzer. The buzzer can be re-
movedwithout affecting this function.
HKS
Input.Pin 8. This is the hookswitchinput to the one
chip phone. This is a high impedance input and
must be switched high for on-hookoperationor low
for off-hook operation. A transition on this input
causes the on chip logic to initialize, terminating
any operationin progressat the time. The signaling
mode defaults to the mode selected at pin 7. Fig-
ures1 and2 illustrate thetiming for this pin.
GND
Pin 9 is the negative line terminal of the device.
This is the voltagereferencefor all specifications.
RXOUT, GRX, RXIN
RXOUT (pin 10), GRX (pin 11) and RXIN (pin 12).
The receive amplifier has one input RXIN and a
non inverting output RXOUT. Amplification from
RXIN to RXOUT is typically 31dB and it can be
adjusted between 11dB and 41dB to suit the sen-
sitivity of the earphone used. The amplification is
proportionalto the external resistor connectedbe-
tween GRX and RXOUT.
FUNCTION PIN DESCRIPTION
(continued)
L3916A
3/14
相關PDF資料 |
PDF描述 |
|---|---|
| L3916AD | SPEECH AND 14 MEMORY DIALER WITH LED DRIVER |
| L3926A | Speech and 14 Memory Dialer With LED Driver(語音電路和14個存儲器的撥號器帶LED驅動器) |
| L3936A | Speech and 14 Memory Dialer With LED Driver(語音電路和14個存儲器的撥號器帶LED驅動器) |
| L4620 | LIQUID LEVEL ALARM |
| L465 | LINEAR INTEGRATED CIRCUITS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L3916A_1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SPEECH AND 14 MEMORY DIALER WITH LED DRIVER |
| L3916AD | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SPEECH AND 14 MEMORY DIALER WITH LED DRIVER |
| L3916AN | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:SPEECH AND 14 MEMORY DIALER WITH LED DRIVER |
| L392 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:THYRISTOR MODULE|SCR|DUAL|INDEPENDENT|240V V(RRM)|15A I(T) |
| L-392 | 制造商:RHOMBUS-IND 制造商全稱:Rhombus Industries Inc. 功能描述:Dual Inductor |
發布緊急采購，3分鐘左右您將得到回復。