- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8895MQ (Micrel Inc)IC ETHERNET SW 5PORT 128-PQFP PDF資料下載
參數資料
| 型號： | KSZ8895MQ |
| 廠商： | Micrel Inc |
| 文件頁數： | 46/119頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ETHERNET SW 5PORT 128-PQFP |
| 標準包裝： | 66 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | MII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 配用： | 576-3871-ND - BOARD EVALUATION FOR KSZ8895MQ |
| 其它名稱： | 576-3753 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
Micrel, Inc.
KSZ8895MQ/RQ/FMQ
Energy Detect Mode
Energy detect mode provides a mechanism to save more power than in the normal operation mode when the
KSZ8895MQ/RQ/FMQ port is not connected to an active link partner. In this mode, the device will save more power
when the cables are unplugged. If the cable is not plugged in, the device can automatically enter a low power state—
the energy detect mode. In this mode, the device will keep transmitting 120ns width pulses at 1 pulse/s rate. Once
activity resumes due to plugging a cable in or attempting by the far end to establish link, the device can automatically
power up to normal power state in energy detect mode.
Energy detect mode consists of two states, normal power state and low power state. While in low power state, the
device reduces power consumption by disabling all circuitry except the energy detect circuitry of the receiver. The
energy detect mode is entered by setting bit [4:3] = 01 in register 14. When the KSZ8895MQ/RQ/FMQ is in this
mode, it will monitor the cable energy. If there is no energy on the cable for a time longer than the pre-configured
value at bit [7:0] Go-Sleep time in register 15, KSZ8895MQ/RQ/FMQ will go into low power state. When
KSZ8895MQ/RQ/FMQ is in low power state, it will keep monitoring the cable energy. Once the energy is detected
from the cable, the device will enter normal power state. When the device is at normal power state, it is able to
transmit or receive packet from the cable.
Soft Power Down Mode
The soft power down mode is entered by setting bit [4:3] = 10 in register 14. When KSZ8895MQ/RQ/FMQ is in this
mode, all PLL clocks are disabled, also all of PHYs and the MACs are off. Any dummy host access will wake-up this
device from current soft power down mode to normal operation mode and internal reset will be issued to make all
internal registers go to the default values.
Power Saving Mode
The power saving mode is entered when auto-negotiation mode is enabled, the cable is disconnected, and by setting
bit[4:3] = 11 in register 14. When KSZ8895MQ/RQ/FMQ is in this mode, all PLL clocks are enabled, MAC is on, all
internal register values will not change, and the host interface is ready for CPU read or write. In this mode, it mainly
controls the PHY transceiver on or off, based on line status to achieve power saving. The PHY continues to transmit,
only turning off the unused receiver block. Once activity resumes, due to plugging a cable or attempting by the far
end to establish link, the KSZ8895MQ/RQ/FMQ can automatically enable the PHY to power up to normal power state
from power saving mode.
During power saving mode, the host CPU can set bit [4:3] in register 14 to change the current power saving mode to
any one of the other three power management operation modes.
Port-based Power Down Mode
In addition, the KSZ8895MQ/RQ/FMQ features a per-port power down mode. To save power, a PHY port that is not
in use can be powered down via the port registers control 13 bit 3, or MIIM PHY registers 0 bit 11.
March 12, 2014
32
Revision 1.7
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8993FL | IC CONV MED 10/100 SGL 128PQFP |
| KSZ8993MLI | IC SWITCH 10/100 3PORT 128-PQFP |
| KSZ8993ML | IC SWITCH 10/100 W/TXRX 128PQFP |
| KSZ8995FQ | IC SWITCH 10/100 5PORT 128-PQFP |
| KSZ8995MA | IC SWITCH 10/100 5PORT 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8895MQ_12 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Integrated 5-Port 10/100 Managed Ethernet Switch with MII/RMII interface |
| KSZ8895MQ-EVAL | 功能描述:以太網開發工具 5-Port 10/100 Ethernet Switch with 1x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8895MQI | 功能描述:以太網 IC 5-Port 10/100 Ethernet Switch with 1x MII Interface (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8895MQXCA | 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:0°C ~ 70°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66 |
| KSZ8895MQXIA | 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:-40°C ~ 85°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66 |
發布緊急采購，3分鐘左右您將得到回復。