- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8895MQ (Micrel Inc)IC ETHERNET SW 5PORT 128-PQFP PDF資料下載
參數資料
| 型號： | KSZ8895MQ |
| 廠商： | Micrel Inc |
| 文件頁數： | 39/119頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ETHERNET SW 5PORT 128-PQFP |
| 標準包裝： | 66 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | MII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 配用： | 576-3871-ND - BOARD EVALUATION FOR KSZ8895MQ |
| 其它名稱： | 576-3753 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
Micrel, Inc.
KSZ8895MQ/RQ/FMQ
Introduction
The KSZ8895MQ/RQ/FMQ contains five 10/100 physical layer transceivers and five media access control (MAC)
units with an integrated Layer 2 managed switch. The device runs in three modes. The first mode is as a five-port
integrated switch. The second is as a five-port switch with the fifth port decoupled from the physical port. In this
mode, access to the fifth MAC is provided through a media independent interface (MII/RMII). This is useful for
implementing an integrated broadband router. The third mode uses the dual MII/RMII feature to recover the use of
the fifth PHY. This allows the additional broadband gateway configuration, where the fifth PHY may be accessed
through the P5-MII/RMII port.
The KSZ8895MQ/RQ/FMQ has the flexibility to reside in a managed or unmanaged design. In a managed design, a
host processor has complete control of the KSZ8895MQ/RQ/FMQ via the SPI bus, or the MDC/MDIO interface. An
unmanaged design is achieved through I/O strapping or EEPROM programming at system reset time.
On the media side, the KSZ8895MQ/RQ/FMQ supports IEEE 802.3 10BASE-T, 100BASE-TX on all copper ports
with Auto MDI/MDIX. The KSZ8895FMQ supports 100BASE-FX on port 3 and port 4. The KSZ8895MQ/RQ/FMQ can
be used as a fully managed five-port switch or hooked up to a microprocessor by its SW-MII/RMII interfaces for any
application solutions.
Physical signal transmission and reception are enhanced through the use of patented analog circuitry that makes the
design more efficient and allows for reduced power consumption and smaller chip die size.
Major enhancements from the KS8895MA/FQ to the KSZ8895MQ/RQ/FMQ include more host interface options, a
dual-switch MAC5 MII and PHY5 MII interfaces with other options, RMII from part of the KSZ8895RQ, tag and port-
based VLAN, rapid spanning tree support, IGMP snooping support, port mirroring support, more flexible rate limiting,
and new filtering functionality.
Functional Overview: Physical Layer Transceiver
100BASE-TX Transmit
The 100BASE-TX transmit function performs parallel-to-serial conversion, 4B/5B coding, scrambling, NRZ-to-NRZI
conversion, MLT3 encoding and transmission. The circuit starts with a parallel-to-serial conversion, which converts
the MII data from the MAC into a 125MHz serial bit stream. The data and control stream is then converted into 4B/5B
coding followed by a scrambler. The serialized data is further converted from NRZ-to-NRZI format, and then
transmitted in MLT3 current output. The output current is set
by an external 1% 12.4k resistor for the 1:1
transformer ratio. It has a typical rise/fall time of 4ns and complies with the ANSI TP-PMD standard regarding
amplitude balance, overshoot, and timing jitter. The wave-shaped 10BASE-T output is also incorporated into the
100BASE-TX transmitter.
100BASE-TX Receive
The 100BASE-TX receiver function performs adaptive equalization, DC restoration, MLT3-to-NRZI conversion, data
and clock recovery, NRZI-to-NRZ conversion, descrambling, 4B/5B decoding, and serial-to-parallel conversion. The
receiving side starts with the equalization filter to compensate for intersymbol interference (ISI) over the twisted pair
cable. Since the amplitude loss and phase distortion is a function of the length of the cable, the equalizer has to
adjust its characteristics to optimize the performance. In this design, the variable equalizer will make an initial
estimation based on comparisons of incoming signal strength against some known cable characteristics, then tunes
itself for optimization. This is an ongoing process and can self-adjust against environmental changes such as
temperature variations.
The equalized signal then goes through a DC restoration and data conversion block. The DC restoration circuit is
used to compensate for the effect of baseline wander and improve the dynamic range. The differential data
conversion circuit converts the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125MHz clock from the edges of the NRZI signal. This recovered clock is then
used to convert the NRZI signal into the NRZ format. The signal is then sent through the de-scrambler followed by
the 4B/5B decoder. Finally, the NRZ serial data is converted to the MII format and provided as the input data to the
MAC.
March 12, 2014
26
Revision 1.7
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8993FL | IC CONV MED 10/100 SGL 128PQFP |
| KSZ8993MLI | IC SWITCH 10/100 3PORT 128-PQFP |
| KSZ8993ML | IC SWITCH 10/100 W/TXRX 128PQFP |
| KSZ8995FQ | IC SWITCH 10/100 5PORT 128-PQFP |
| KSZ8995MA | IC SWITCH 10/100 5PORT 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8895MQ_12 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Integrated 5-Port 10/100 Managed Ethernet Switch with MII/RMII interface |
| KSZ8895MQ-EVAL | 功能描述:以太網開發工具 5-Port 10/100 Ethernet Switch with 1x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8895MQI | 功能描述:以太網 IC 5-Port 10/100 Ethernet Switch with 1x MII Interface (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8895MQXCA | 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:0°C ~ 70°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66 |
| KSZ8895MQXIA | 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:-40°C ~ 85°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66 |
發布緊急采購，3分鐘左右您將得到回復。