- 您現在的位置：買賣IC網 > PDF目錄16827 > KSZ8895MQ-EVAL (Micrel Inc)BOARD EVALUATION FOR KSZ8895MQ PDF資料下載
參數資料
| 型號： | KSZ8895MQ-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 64/119頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR KSZ8895MQ |
| 標準包裝： | 1 |
| 主要目的： | 接口，以太網控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8895MQ |
| 已供物品： | 板 |
| 相關產品： | 576-3753-ND - IC ETHERNET SW 5PORT 128-PQFP |
| 其它名稱： | 576-3871 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
Micrel, Inc.
KSZ8895MQ/RQ/FMQ
Figure 13. KSZ8895MQ/RQ/FMQ EEPROM Configuration Timing Diagram
To configure the KSZ8895MQ/RQ/FMQ with a pre-configured EEPROM use the following steps:
1.
At the board level, connect pin 110 on the KSZ8895MQ/RQ/FMQ to the SCL pin on the EEPROM. Connect pin
111 on the KSZ8895MQ/RQ/FMQ to the SDA pin on the EEPROM.
2.
A[2-0] address pins of EEPROM should be tied to ground for address A[2-0] = ‘000’ to be identified by the
KSZ8895MQ/RQ/FMQ.
3.
Set the input signals PS[1:0] (pins 113 and 114, respectively) to “00.” This puts the KSZ8895MQ/RQ/FMQ serial
bus configuration into I
2C master mode.
4.
Be sure the board-level reset signal is connected to the KSZ8895MQ/RQ/FMQ reset signal on pin 115 (RST_N).
5.
Program the contents of the EEPROM before placing it on the board with the desired configuration data. Note
that the first byte in the EEPROM must be “95” for the loading to occur properly. If this value is not correct, all
other data will be ignored.
6.
Place EEPROM on the board and power up the board. Assert the active-low board level reset to RST_N on the
KSZ8895MQ/RQ/FMQ. After the reset is de-asserted, the KSZ8895MQ/RQ/FMQ will begin reading configuration
data from the EEPROM. The configuration access time (tprgm) is less than 30ms.
Note: For proper operation, make sure that pin 47 (PWRDN_N) is not asserted during the reset operation.
SPI Slave Serial Bus Configuration
The KSZ8895MQ/RQ/FMQ can also act as a SPI slave device. Through the SPI, the entire feature set can be
enabled, including “VLAN,” “IGMP snooping,” “MIB counters,” etc. The external master device can access any
register from Register 0 to Register 255 randomly. The system should configure all the desired settings before
enabling the switch in the KSZ8895MQ/RQ/FMQ. To enable the switch, write a "1" to Register 1 bit 0.
Two standard SPI commands are supported (00000011 for “READ DATA,” and 00000010 for “WRITE DATA”). To
speed configuration time, the KSZ8895MQ/RQ/FMQ also supports multiple reads or writes. After a byte is written to
or read from the KSZ8895MQ/RQ/FMQ, the internal address counter automatically increments if the SPI Slave
Select Signal (SPIS_N) continues to be driven low. If SPIS_N is kept low after the first byte is read, the next byte at
the next address will be shifted out on SPIQ. If SPIS_N is kept low after the first byte is written, bits on the Master
Out Slave Input (SPID) line will be written to the next address. Asserting SPIS_N high terminates a read or write
operation. This means that the SPIS_N signal must be asserted high and then low again before issuing another
command and address. The address counter wraps back to zero once it reaches the highest address. Therefore the
entire register set can be written to or read from by issuing a single command and address.
The default SPI clock speed is 12.5MHz. The KSZ8895MQ/RQ/FMQ is able to support a SPI bus up to 25MHz (set
register 12 bit[5:4] = 0x10). A high performance SPI master is recommended to prevent internal counter overflow.
March 12, 2014
49
Revision 1.7
相關PDF資料 |
PDF描述 |
|---|---|
| 202D285-3/42-0 | BOOT MOLDED |
| 0210391086 | CABLE JUMPER 1MM .178M 37POS |
| 202F221-50-0 | BOOT MOLDED |
| 222F274-51-0 | BOOT MOLDED |
| 202A196-25-0 | BOOT MOLDED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8895MQI | 功能描述:以太網 IC 5-Port 10/100 Ethernet Switch with 1x MII Interface (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8895MQXCA | 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:0°C ~ 70°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66 |
| KSZ8895MQXIA | 功能描述:Ethernet Switch 10/100 Base-T/TX I2C, SPI Interface 128-PQFP (14x20) 制造商:microchip technology 系列:- 包裝:托盤 零件狀態:有效 協議:以太網 功能:開關 接口:I2C，SPI 標準:10/100 Base-T/TX 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:129mA 工作溫度:-40°C ~ 85°C 封裝/外殼:128-BFQFP 供應商器件封裝:128-PQFP（14x20） 標準包裝:66 |
| KSZ8895RQ | 功能描述:以太網 IC 5-port Switch, one SW5-RMII and one P5-RMII Interface RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8895RQ TR | 功能描述:以太網 IC 5-port Switch, one SW5-RMII and one P5-RMII Interface RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。