- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8873MLLJ (Micrel Inc)IC ETHERNET SWITCH 3PORT 64LQFP PDF資料下載
參數資料
| 型號： | KSZ8873MLLJ |
| 廠商： | Micrel Inc |
| 文件頁數： | 40/108頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ETHERNET SWITCH 3PORT 64LQFP |
| 特色產品： | KSZ8873MLLJ Ethernet Switches |
| 標準包裝： | 160 |
| 系列： | * |
| 其它名稱： | 576-3996 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
Micrel, Inc.
KSZ8873MLLJ
September 2011
37
M9999-091911-1.8
Figure 9. EEPROM Configuration Timing Diagram
The following is a sample procedure for programming the KSZ8873MLLJ with a pre-configured EEPROM:
1. Connect the KSZ8873MLLJ to the EEPROM by joining the SCL and SDA signals of the respective devices.
2. Enable I
2C master mode by setting the KSZ8873MLLJ strap-in pins, P2LED[1:0] to “00”.
3. Check to ensure that the KSZ8873MLLJ reset signal input, RSTN, is properly connected to the external reset source
at the board level.
4. Program the desired configuration data into the EEPROM.
5. Place the EEPROM on the board and power up the board.
6. Assert an active-low reset to the RSTN pin of the KSZ8873MLLJ. After reset is de-asserted, the KSZ8873MLLJ
begins reading the configuration data from the EEPROM. The KSZ8873MLLJ checks that the first byte read from the
EEPROM is “88”. If this value is correct, EEPROM configuration continues. If not, EEPROM configuration access is
denied and all other data sent from the EEPROM is ignored by the KSZ8873MLLJ.
Note:
For proper operation, check to ensure that the KSZ8873MLLJ PWRDN input signal is not asserted during the reset
operation. The PWRDN input is active low.
I2C Slave Serial Bus Configuration
In managed mode, the KSZ8873MLLJ can be configured as an I
2C slave device. In this mode, an I2C master device
(external controller/CPU) has complete programming access to the KSZ8873MLLJ’s 198 registers. Programming access
includes the Global Registers, Port Registers, Advanced Control Registers and indirect access to the “Static MAC Table”,
“VLAN Table”, “Dynamic MAC Table,” and “MIB Counters.” The tables and counters are indirectly accessed via registers
121 to 131.
In I
2C slave mode, the KSZ8873MLLJ operates like other I2C slave devices. Addressing the KSZ8873MLLJ’s 8-bit
registers is similar to addressing Atmel’s AT24C02 EEPROM’s memory locations. Details of I
2C read/write operations and
related timing information can be found in the AT24C02 Datasheet.
Two fixed 8-bit device addresses are used to address the KSZ8873MLLJ in I
2C slave mode. One is for read; the other is
for write. The addresses are as follow:
1011_1111 <read>
1011_1110 <write>
The following is a sample procedure for programming the KSZ8873MLLJ using the I
2C slave serial bus:
1. Enable I
2C slave mode by setting the KSZ8873MLLJ strap-in pins P2LED[1:0] to “01”.
2. Power up the board and assert reset to the KSZ8873MLLJ. Configure the desired register settings in the
KSZ8873MLLJ, using the I
2C write operation.
3. Read back and verify the register settings in the KSZ8873MLLJ, using the I
2C read operation.
Some of the configuration settings, such as “Aging enable”, “Auto Negotiation Enable”, “Force Speed” and “Power down”
can be programmed after the switch has been started.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8873MMLI | IC ETHERNET SWITCH 3PORT 64LQFP |
| KSZ8893FQL | IC SWITCH FAST ETH 3PORT 128PQFP |
| KSZ8895MQI | IC ETHERNET SWITCH 5PORT 128PQFP |
| KSZ8895MQ | IC ETHERNET SW 5PORT 128-PQFP |
| KSZ8993FL | IC CONV MED 10/100 SGL 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8873MML | 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 2x MII Interface, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8873MML-EVAL | 功能描述:以太網開發工具 3-Port Fast Ethernet Switch with 2x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8873MMLI | 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 2x MII Interface (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8873RLL | 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 1x RMII Interface, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8873RLL-EVAL | 功能描述:以太網開發工具 3-Port Fast Ethernet Switch with 1x RMII Interface - Evalaution Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。