- 您現在的位置：買賣IC網 > PDF目錄16855 > KSZ8851-16MLL-EVAL (Micrel Inc)BOARD EVALUATION KSZ8851-16MLL PDF資料下載
參數資料
| 型號： | KSZ8851-16MLL-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 2/84頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION KSZ8851-16MLL |
| 產品培訓模塊： | KSZ8851 10/100 Embedded Controllers |
| 標準包裝： | 1 |
| 系列： | LinkMD® |
| 主要目的： | 接口，以太網控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8851-16MLL |
| 主要屬性： | 1 個端口，100BASE-TX/10BASE-T |
| 次要屬性： | 8/16 位接口，LinkMD 線纜診斷 |
| 已供物品： | 板，文檔 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 相關產品： | 576-3438-ND - IC CTLR MAC/PHY NON PCI 128PQFP 576-3253-ND - IC CTLR MAC/PHY NON-PCI 128-PQFP 576-3252-ND - IC CTLR MAC/PHY NON-PCI 48-LQFP |
| 其它名稱： | 576-3292 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
Micrel, Inc.
KSZ8851-16MLL/MLLI
March 11, 2014
10
Revision 2.2
Pin Description
Pin Number
Pin Name
Type
Pin Function
1
P1LED1
IPU/O
Programmable LED output to indicate port activity/status.
LED is ON when output is LOW; LED is OFF when output is HIGH.
Port 1 LED indicators
1 defined as follows:
Chip Global Control Register: CGCR bit [9]
0 (Default)
1
P1LED1
100BT
ACT
P1LED0
LINK/ACT
LINK
1. Link = LED On; Activity = LED Blink; Link/Act = LED On/Blink;
Speed = LED On (100BASE-T); LED Off (10BASE-T)
Config Mode: The P1LED1 pull-up/pull-down value is latched as 16/8-bit mode during
power-up / reset. See “Strapping Options” section for details
2
P1LED0
OPU
3
PME
OPU
Power Management Event (default active low): It is asserted (low or high depends on
polarity set in PMECR register) when one of the wake-on-LAN events is detected by
KSZ8851-16MLL. The KSZ8851-16MLL is requesting the system to wake up from low
power mode.
4
INTRN
OPU
Interrupt: An active low signal to host CPU to indicate an interrupt status bit is set, this pin
need an external 4.7K pull-up resistor.
5
RDN
IPU
Read Strobe Not
Asynchronous read strobe, active low to indicate read cycle.
6
WRN
IPU
Write Strobe Not
Asynchronous write strobe, active low to indicate write cycle.
7
DGND
GND
Digital ground
8
VDD_CO1.8
P
1.8V regulator output . This 1.8V output pin provides power to pins 14 (VDD_A1.8) and 29
(VDD_D1.8) for core VDD supply.
If VDD_IO is set for 1.8V then this pin should be left floating, pins 14 (VDD_A1.8) and 29
(VDD_D1.8) will be sourced by the external 1.8V supply that is tied to pins 27, 38 and 46
(VDD_IO) with appropriate filtering.
9
EED_IO
IPD/O
In/Out Data from/to external EEPROM.
Config Mode: The pull-up/pull-down value is latched as with/without EEPROM during
power-up / reset. See “Strapping Options” section for details
10
EESK
IPD/O
EEPROM Serial Clock
A 4
s (OBCR[1:0]=11 on-chip bus speed @ 25MHz) or 800ns (OBCR[1:0]=00 on-chip
bus speed @ 125MHz) serial output clock cycle to load configuration data from the serial
EEPROM.
Config Mode: The pull-up/pull-down value is latched as big/little endian mode during
power-up / reset. See “Strapping Options” section for details
11
CMD
IPD
Command Type
This command input decides the SD[15:0] shared data bus access information.
When command input is low, the access of shared data bus is for data access in 16-bit
mode shared data bus SD[15:0] or in 8-bit mode shared data bus SD[7:0].
When command input is high, the access of shared data bus is for address A[7:2] access
at shared data bus SD[7:2], byte enable BE[3:0] at SD[15:12] and the SD[11:8] is “Do Not
Care” in 16-bit mode. It is for address A[7:0] access at SD[7:0] in 8-bit mode.
相關PDF資料 |
PDF描述 |
|---|---|
| MLF2012DR15M | INDUCTOR MULTILAYER .15UH 0805 |
| 0210491067 | CABLE JUMPER 1.25MM .203M 35POS |
| MLF2012A4R7M | INDUCTOR MULTILAYER 4.7UH 0805 |
| RNF-100-3/16-BK-STK | HEATSHRINK RNF-100 3/16"X4' BLK |
| EVAL-ADF4158EB1Z | BOARD EVALUATION FOR ADF4158 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8851-16MLL-EVAL | 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8851-16MLL |
| KSZ8851-16MLLI | 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-bit) Bus Interface (I-Temp, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發(fā)器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8851-16MLLI TR | 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with Generic (8, 16-bit) Bus Interface (I-Temp, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發(fā)器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8851-16MLLJ | 功能描述:以太網 IC Single-Port Ethernet MAC Controller with 8/16-Bit Non-PCI Interface (125C support) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發(fā)器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8851-16MLLJ_10 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Single-Port Ethernet MAC Controller with 8-Bit or 16-Bit Non-PCI Interface |
發(fā)布緊急采購，3分鐘左右您將得到回復。