參數資料
型號： KMC755CVT400LE
廠商： Freescale Semiconductor
文件頁數： 41/56頁
文件大?。?/td> 0K
描述： IC MPU 32BIT 400MHZ 360-FCPBGA
標準包裝： 1
系列： MPC7xx
處理器類型： 32-位 MPC7xx PowerPC
速度： 400MHz
電壓： 2V
安裝類型： 表面貼裝
封裝/外殼： 360-BBGA，F(xiàn)CCBGA
供應商設備封裝： 360-FCCBGA（25x25）
包裝： 托盤
MPC755 RISC Microprocessor Hardware Specifications, Rev. 8
46
Freescale Semiconductor
System Design Information
Figure 26. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
8.8.2
Adhesives and Thermal Interface Materials
A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the
thermal contact resistance. For those applications where the heat sink is attached by spring clip
mechanism, Figure 27 shows the thermal performance of three thin-sheet thermal-interface materials
(silicone, graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function of contact
pressure. As shown, the performance of these thermal interface materials improves with increasing contact
pressure. The use of thermal grease significantly reduces the interface thermal resistance. That is, the bare
joint results in a thermal resistance approximately seven times greater than the thermal grease joint.
Heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see
Figure 25). This spring force should not exceed 5.5 pounds of force. Therefore, the synthetic grease offers
the best thermal performance, considering the low interface pressure. Of course, the selection of any
thermal interface material depends on many factors—thermal performance requirements,
manufacturability, service temperature, dielectric properties, cost, etc.
Figure 27 describes the thermal performance of select thermal interface materials.
External Resistance
Radiation
Convection
Radiation
Convection
Heat Sink
Printed-Circuit Board
Thermal Interface Material
(Note the internal versus external package resistance.)
Internal Resistance
Die/Package
Package/Leads
Die Junction
相關PDF資料
PDF描述
KMPC823ZQ75B2T IC MPU PWRQUICC 75MHZ 256-PBGA
KMPC8241TVR166D IC MPU 32BIT 166MHZ 357-PBGA
KMPC8241TZQ200D IC MPU 32BIT 200MHZ 357-PBGA
KMPC8245ARZU400D IC MPU 32BIT 400MHZ 352-TBGA
KMPC8245LZU350D IC MPU 32BIT 350MHZ 352-TBGA
相關代理商/技術參數
參數描述
KMC7D0CN20C 制造商:KEC 制造商全稱:KEC(Korea Electronics) 功能描述:TSSOP-8 PACKAGE
KMC7D0CN20CA 制造商:KEC 制造商全稱:KEC(Korea Electronics) 功能描述:Common N-Ch Trench MOSFET
KMC7D0CN20CA_0812 制造商:KEC 制造商全稱:KEC(Korea Electronics) 功能描述:Common N-Ch Trench MOSFET
KMC8112TMP2400V 功能描述:IC DSP 300MHZ 431FCPBGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
KMC8112TVT2400V 功能描述:IC DSP 300MHZ 431FCPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:StarCore 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*