- 您現在的位置：買賣IC網 > PDF目錄374354 > KM41V4000D (SAMSUNG SEMICONDUCTOR CO. LTD.) RES,Film,0.33Ohms,250WV,200ppm-TC,4112-Case RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | KM41V4000D |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | RES,Film,0.33Ohms,250WV,200ppm-TC,4112-Case RoHS Compliant: Yes |
| 中文描述： | 4米× 1位的CMOS動態隨機存儲器的快速頁面模式 |
| 文件頁數： | 8/20頁 |
| 文件大小： | 340K |
| 代理商： | KM41V4000D |
KM41C4000D, KM41V4000D
CMOS DRAM
NOTES
An initial pause of 200us is required after power-up followed by any 8 RAS-only refresh or CAS-before-RAS refresh cycles
before proper device operation is achieved.
V
IH
(min) and V
IL
(max) are reference levels for measuring timing of input signals. Transition times are measured between
V
IH
(min) and V
IL
(max) and are assumed to be 5ns for all inputs.
Measured with a load equivalent to 2 TTL(5V)/1 TTL(3.3V) loads and 100pF.
Operation within the
t
RCD
(max) limit insures that
t
RAC
(max) can be met.
t
RCD
(max) is specified as a reference point only.
If
t
RCD
is greater than the specified
t
RCD
(max) limit, then access time is controlled exclusively by
t
CAC
.
Assumes that
t
RCD
≥
t
RCD
(max).
This parameter defines the time at which the output achieves the open circuit condition and is not referenced to V
oh
or V
ol
.
t
WCS
,
t
RWD
,
t
CWD
,
t
AWD
and
t
CPWD
are non restrictive operating parameters. They are included in the data sheet as electrical
characteristics only. If
t
WCS
≥
t
WCS
(min), the cycle is an early write cycle and the data output will remain high impedance for
the duration of the cycle. If
t
CWD
≥
t
CWD
(min),
t
RWD
≥
t
RWD
(min),
t
AWD
≥
t
AWD
(min) and
t
CPWD
≥
t
CPWD
(min) then the cycle is a
read-modify-write cycle and the data output will contain the data read from the selected address. If neither of the above con-
ditions is satisfied, the condition of the data out is indeterminate.
Either
t
RCH
or
t
RRH
must be satisfied for a read cycle.
These parameters are referenced to CAS falling edge in early write cycles and to W falling edge in read-modify-write cycles.
Operation within the
t
RAD
(max) limit insures that
t
RAC
(max) can be met.
t
RAD
(max) is specified as a reference point only.
If
t
RAD
is greater than the specified
t
RAD
(max) limit, then access time is controlled by
t
AA
.
These specifiecations are applied in the test mode.
In test mode read cycle, the value of
t
RAC
,
t
AA
,
t
CAC
is delayed by 2ns to 5ns for the specified values. These parameters
should be specified in test mode cycles by adding the above value to the specified value in this data sheet.
t
OFF(MAX)
defines the time at which the output achieves the open circuit condition and are not referenced to output voltage
level.
If
t
RASS
≥
100us, then RAS precharge time must use
t
RPS
instead of
t
RP
.
For RAS-only refresh and burst CAS-before-RAS refresh mode, 1024(1K) cycle of burst refresh must be executed within
16ms before and after self refresh, in order to meet refresh specification.
For distributed CAS-before-RAS with 15.6us interval, CAS-before-RAS refresh should be executed with in 15.6us immedi-
ately before and after self refresh in order to meet refresh specification.
7.
6.
5.
10.
9.
8.
13.
12.
11.
14.
3.
2.
1.
4.
15.
16.
相關PDF資料 |
PDF描述 |
|---|---|
| KM4211IM8TR3 | Dual, 0.2mA, Low Cost, +2.7V & +5V, 35MHz Rail-to-Rail Amp |
| KM4211 | Dual, 0.2mA, Low Cost, +2.7V & +5V, 35MHz Rail-to-Rail Amp |
| KM4211IM8 | Dual, 0.2mA, Low Cost, +2.7V & +5V, 35MHz Rail-to-Rail Amp |
| KM4211IC8 | Multiconductor Cable; Number of Conductors:9; Conductor Size AWG:18; No. Strands x Strand Size:19 x 30; Jacket Material:Polyvinylchloride (PVC); Leaded Process Compatible:Yes; Conductor Material:Copper; Features:Unshielded RoHS Compliant: Yes |
| KM4211IC8TR3 | Multiconductor Cable; Number of Conductors:9; Conductor Size AWG:18; No. Strands x Strand Size:19 x 30; Jacket Material:Polyvinylchloride (PVC); Conductor Material:Copper; Features:Unshielded; Leaded Process Compatible:Yes RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KM4200 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Dual, Low Cost, +2.7V & +5V, 260MHz Rail-to-Rail Amplifier |
| KM4200IC8 | 功能描述:高速運算放大器 SOIC-8 RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| KM4200IC8TR3 | 功能描述:運算放大器 - 運放 Dual RRO amplifier 26Mhz RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| KM4200IC8TR3_NL | 功能描述:高速運算放大器 RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| KM4200IC8TR3_Q | 功能描述:運算放大器 - 運放 Dual RRO amplifier 26Mhz RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。