- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL96017WIRT8Z (INTERSIL CORP) 128-Tap DCP, 16kbit EEPROM, and I2C Serial Interface PDF資料下載
參數資料
| 型號： | ISL96017WIRT8Z |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | 128-Tap DCP, 16kbit EEPROM, and I2C Serial Interface |
| 中文描述： | 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 128 POSITIONS, PDSO8 |
| 封裝： | 3 X 3 MM, 0.80 MM HEIGHT, 0.65 MM PITCH, ROHS COMPLIANT, PLASTIC, TDFN-8 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 330K |
| 代理商： | ISL96017WIRT8Z |
8
FN8243.1
April 17, 2006
I
2
C Serial Interface
This device supports a bidirectional bus oriented protocol.
The protocol defines any device that sends data onto the
bus as a transmitter and the receiving device as the receiver.
The device controlling the transfer is a master and the
device being controlled is the slave. The master always
initiates data transfers and provides the clock for both
transmit and receive operations. Therefore, this device
operates as a slave device in all applications. All
communication over the I
2
C interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (See
Figure 6). On power up, the SDA pin is in the input mode. All
I
2
C interface operations must begin with a START condition,
which is a HIGH to LOW transition of SDA while SCL is
HIGH. The device continuously monitors the SDA and SCL
lines for the START condition and does not respond to any
command until this condition is met (See Figure 6). A START
condition is ignored during the power up sequence and
during internal non-volatile write cycles. All I
2
C interface
operations must be terminated by a STOP condition, which
is a LOW to HIGH transition of SDA while SCL is HIGH (See
Figure 6). A STOP condition at the end of a Read operation,
or at the end of a Write operation to volatile bytes only
places the device in its standby mode. A STOP condition
during a Write operation to a non-volatile byte, initiates an
internal non-volatile write cycle. The device enters its
standby state when the internal non-volatile write cycle is
completed.
An ACK, Acknowledge, is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (See Figure 7). This device
responds with an ACK after recognition of a START
condition followed by a valid Identification Byte, and once
again after successful receipt of the Address Byte. This
device also responds with an ACK after receiving each Data
Byte of a Write operation. The master must respond with an
ACK after receiving each Data Byte of a read operation
except the last one. A valid Identification Byte contains 1010
as the four MSBs. The following three bits are the MSBs of
the memory address to be accessed. The LSB of the
Identification Byte is the Read/Write bit. Its value is “1” for a
Read operation, and “0” for a Write operation (See Table 2).
The complete memory address location to be accessed is a
11-bit word, since the memory has 2048 bytes. The eight
LSBs are in the Address Byte.
TABLE 2. IDENTIFICATION BYTE FORMAT
1
0
1
0
A10
A9
A8
R/Wb
MSB
LSB
SCL
SDA
START
STOP
SCL
SDA
DATA STABLE
DATA CHANGE
DATA STABLE
FIGURE 6. VALID DATA CHANGES, START AND STOP CONDITIONS
ISL96017
相關PDF資料 |
PDF描述 |
|---|---|
| ISL97516 | 600kHz/1.2MHz PWM Step-Up Regulator |
| ISL97516_07 | 600kHz/1.2MHz PWM Step-Up Regulator |
| ISL97516IUZ | 600kHz/1.2MHz PWM Step-Up Regulator |
| ISL97516IUZ-T | 600kHz/1.2MHz PWM Step-Up Regulator |
| ISL97516IUZ-TK | 600kHz/1.2MHz PWM Step-Up Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL96017WIRT8Z-T | 功能描述:IC XDCP 128-TAP 10KOHM 8-TDFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| ISL96017WIRT8Z-TK | 功能描述:IC XDCP 128-TAP 10KOHM 8-TDFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| ISL97516IUZ | 功能描述:直流/直流開關轉換器 600KHZ/1.2MHZ PWM ST EP-UP REG 8LD RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| ISL97516IUZEVALZ | 制造商:Intersil Corporation 功能描述:ISL97516IUZ EVALUATION BOARD - 8LD MSOP - ROHS COMPLIANT - Bulk 制造商:Intersil Corporation 功能描述:EVALUATION BOARD FOR ISL97516IUZ 制造商:Intersil 功能描述:ISL97516IUZ EVALI ON BRD 8LD RHS CMPL |
| ISL97516IUZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL97516IUZ RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。